浇注系统设计.ppt

模具設計的優先順序 Priorities of Mold Design,澆注系統設計 (Filling System Design) 排氣系統設計 (Venting System Design) 冷卻系統設計 (Cooling System Design) 脫模系統設計 (Ejecting System Design),澆注系統設計的優先順序 Priorities of Filling System Design,產品設計 (Part Design) 型腔設計 (Cavity Design) 澆口設計 (Gate Design) 流道設計 (Runner Design) 噴嘴設計 (Nozzle Design),典型的澆注系統 Typical Filling System,壁厚不均是注塑成型中最大的麻煩製造者。 這對薄壁產品尤然。 這些麻煩包括了遲滯現象、短射、凹陷、發赤、噴流、翹曲及長冷卻時間等；目前都可用CAE以直接或間接的方式預測。 Non-uniform wall thickness is the biggest trouble maker in plastic injection molding. This is especially true to thin-wall part. The troubles, including hesitation, short shot, sink mark, blush, jetting, warpage and long cooling time etc., can be predicted, directly or indirectly, by using CAE.,壁厚不均 Non-uniform Wall Thickness,壁厚設計 Wall Thickness Design,掏空設計 (1) Coring Out Design (1),掏空設計 (2) Coring Out Design (2),氣泡或/和凹陷的形成 Void or/and Sink Mark Forming,肋厚和內圓角半徑的影響 The Effect of Rib Thickness & Fillet Radius,肋的底部厚度 Bottom Thickness of Rib,肋的設計 (1 ) Rib Design ( 1 ),肋的設計 (2) Rib Design ( 2 ),肋的設計 (3) Rib Design ( 3 ),與側壁相連之凸轂 (熱塑性塑膠) Boss at Wall ( Thermoplastics ),遠離側壁之凸轂 (熱塑性塑膠) Boss Away From Wall ( Thermoplastics ),外側凸轂 Outside Boss,Where 1/r : 樑的曲率 curvature of the beam M : 彎曲力矩 bending moment E : 彈性模數 modulus of elasticity I : 斷面積對中立軸的慣性矩 moment of inertia of the cross- sectional area with respect to the neutral axis EI : 撓曲剛性 flexural rigidity,撓曲剛性 Flexural Rigidity,A variety of molded-in interlocks can add stiffness to thin-wall housing designs.,各種一體成型的內鎖件 能增加薄殼的剛性。,結構設計是薄殼成型零件的基礎。 Structural design is the base of thin-wall molding parts. 薄殼成型產品不僅僅是一趨勢，而且也是降低成本和提高競爭力的有效途徑。 Thin-wall molding part is not only a trend but also an effective way to achieve cost reduction and competitiveness increase.,結構設計和薄殼成型產品 Structural Design & Thin-wall Molding Parts,熔膠波前推進 Melt-Front Advancement,充填模式,積風和熔接線 Filling Patterns, Air-Traps and Weld Lines Location,熔接線 Weld Lines,材料 Material : PC-GF50,原設計 Original,更改設計 Revised,更改澆口位置以重新定位熔接線 Weld Lines Can Be Relocated By Changing Gate Location,典型對頭熔接線伸張強度保留值 Typical Butt Weld Tensile Strength Retention Values,熔接線冷料井 Weld Slug Well,對頭熔接線 Butt weld,熔接線冷料井 Weld slug well,積風 Air Traps,排氣 Vent,每增加一個澆口，至少增加一條熔接線，同時增加一個澆口痕跡、增加流道的體積以及增加較多的積風。 Every time one gate is added, one weld line, at least, one gate mark, more runner volume and more air traps will be added. 在型腔能夠完滿充填的前提下，澆口數目是愈少愈好。 As long as the cavity is able to be filled appropriately, gates are the less the better. 為了減少澆口數目，每一澆口應就塑流力所能及的流長/壁厚比之內，找出可以涵蓋最大產品面積的進澆位置。 In order to reduce the number of gates, each gate shall be located at where the melt is able to cover maximum part area based on the largest melt flow length/thickness ratio.,澆口數目 The Number of Gates,充填均衡 Flow Balance,熔膠波前於同一時間抵達型腔各末端。 Melt front reaches the ends of cavity at the same time.,洗衣機圈板,洗衣機圈板,冷氣通風飾罩-原始設計 Air-conditioner Grille - Original,18 gates pressure: 76 MPa,冷氣通風飾罩-修正設計 Air-conditioner Grille - Revised,8 gates pressure: 75 MPa,分析結果比較表 Comparison of Analysis Results,十二澆口設計 12 Gate Design,四澆口設計 4 Gate Design,電子零件置物箱四澆口 和十二澆口設計比較表,如何快速平衡眾多模穴之流道 How to Balance Flow In A Multi-cavity Mold,一排支流道之不平衡充填 Unbalanced Flow In A Branch,一排支流道平衡後之充填 Balanced Flow In A Branch,全模具(128模穴)之不平衡充填 Unbalanced Flow In A Mold,全模具(128模穴)平衡後之充填 Balanced Flow In A Mold,The melt fills the inside cavities before filling the outside cavities.,The runner system shows that warmer, low-viscosity material (yellow and red) follows the inside wall when the melt splits at an intersection.,Melt ” Flipper ”,導致平直產品的澆口設計 Gate Design for Flat Part,澆口設計(減少滯流效應) Gate Design to Avoid Hesitation,沒有遲滯現象,幫浦零件 (Part, Pump) 塑料 (Polymer): POM,澆口設計(避免凹陷和氣泡) Gate Design to Avoid Sink Mark & Void,使用重疊澆口以避免噴流 Avoid Jetting by Using Overlap Gate,正確的澆口位置以避免噴流 Avoid Jetting by Locating Gate Correctly,使用凸片澆口以避免噴流 Avoid Jetting by Using Tab Gate,使用適當的澆口形狀以避免噴流 Avoid Jetting by Profiling Gate Properly,幫浦零件(Part, Pump) 塑料(Polymer): POM 進澆處(Polymer entrance)： 澆口厚(Gate thickness) 1.2mm，模穴厚(Cavity thickness) 3.2mm 問題 (Problem)： 噴流(Jetting),Poor Design Causing Jetting,氣輔成型冰箱把手,閥澆口 Valve Gate,1. 閥澆口梢 Valve-Gate Pin 2. 加熱管 Heater 3. O型環 #610 “0“ Ring 4. 流道歧管模板 Manifold Plate 5. 軸封環 Seal Retainer 6. 套筒軸封 Sleeve Seal 7. 枕塊 Support Pillar 8. 油壓缸 Hydraulic Cylinder,閥澆口 (1) Valve Gate ( 1 ),全部閥澆口同時打開時之充填狀況 Mold filling with all the valve gates ( shut-off gates ) opened at the same time.,閥澆口 (2) Valve Gate ( 2 ),部份閥澆口延遲打開，改變充填模式 Mold filling with delayed valve gate opening; filling pattern, weld lines and air traps are changed.,多澆口設計 Multi-Gate Design,閥式澆口 Valve Gate,澆口種類 Gate Types,矩形邊緣澆口設計 Rectangular Edge Gate Design,扇形澆口設計 Fan Gate Design,重疊式澆口設計 Overlap Gate Design,凸耳澆口設計 Tab Gate Design,針點澆口設計 Pin Gate Design,潛伏式澆口設計 Subgate Design,剪切速率 Shear Rate,剪 切 應 力 shear Stress 黏 度 viscosity 剪 切 速 率 shear rate,剪切應力 Shear Stress,水力直徑 Hydraulic Diameter,Where is the hydraulic diameter 水力直徑 A is the cross-sectional area of the flow 流路斷面積 P is the wetted perimeter 濕周長,水力直徑 Hydraulic Diameter,在不同剖面形狀，相同斷面積下之變化 Various runner profiles, based on the same cross-sectional area,流道尺寸設計 (1) Runner Sizing (1),D : 流道直徑 ( mm ) runner diameter in mm W : 下游塑膠重量 ( g ) downstream plastic weight L : 流道長度 ( mm ) runner length in mm,流道尺寸設計 (2) Runner Sizing (2),流道尺寸設計 (3) Runner Sizing (3),流道尺寸設計 (4) Runner Sizing (4),流道尺寸設計(A1) Runner Sizing (A1),G : 重量 weight S : 零件厚度 thickness D' : 參考直徑 reference diameter,流道尺寸設計(A2) Runner Sizing (A2),G : 重量 weight S : 零件厚度 thickness D' : 參考直徑 reference diameter,流道尺寸設計(B) Runner Sizing (B),D' : 參考直徑 reference diameter L : 長度 length fL : 長度係數 Length coefficient D : 流道直徑 runner diameter,冷料井設計 Cold Slug Well Design,冷料井設計 Cold Slug Well Design,澆道襯套尺寸 Sprue Bushing Sizing,