《RD-JT9192DownloadToolmethod.ppt》由会员分享,可在线阅读,更多相关《RD-JT9192DownloadToolmethod.ppt(17页珍藏版)》请在三一文库上搜索。
1、RD-JT92 and RD-JT91 Download Tool RD - JT91 and RD - JT92 download Tool can be used for common use. However, youd be bettermore attention in downloading the program because the two models program file names are different. Install method 1. At first, double click DLP Composer Lite v3.7 setup.exe file
2、 in the download 2.Click next button RD-JT92 and RD-JT91 Download Tool Down scrollbar until bottom Select this radio button 3.Click next button RD-JT92 and RD-JT91 Download Tool 4.Click next button RD-JT92 and RD-JT91 Download Tool 5.Click next button RD-JT92 and RD-JT91 Download Tool 6.Click next b
3、utton RD-JT92 and RD-JT91 Download Tool 6.Click finish button RD-JT92 and RD-JT91 Download Tool 7.If pushed Yes, your computer rebooting. and then the end. RD-JT92 and RD-JT91 Download Tool USB Support - Installation (All Platforms) This release includes support for a USB communications interface to
4、 DDP2000-based projectors. The setup program includes the files needed to install USB support (for Win98/WinMe/Win2K/WinXP only - Win95 and WinNT are not supported). After DLP Composer Lite is installed, to install the USB support, choose the “Install DDP2000 USB Driver“ icon under “DLP Composer Lit
5、e“ in your Start menu. USB Support - Win98/WinMe Only Installation on Windows 98 or Windows Me may prompt “Please insert the disk labeled DLP Composer Installation Directory, and then click OK“. This message may be safely ignored by clicking the OK button. Another prompt will then appear: “The file
6、windrvr6.sys on DLP Composer Installation Directory cannot be found“. Again, click OK and the installation proceeds without further problems. USB Support - Using a projector for the first time After installation is complete, and you plug a DDP2000-based projector into USB for the first time, Windows
7、 will run the “New Hardware Wizard“. When the wizard prompts to find the necessary drivers, accept the recommended choice (let the system find the driver for you) and click “Next“ to complete the installation. Note: The Windows 98/Me “New Hardware Wizard“ may not automatically find the driver. You s
8、hould use the “Advanced“ option, and enter the directory where the DLP Composer Lite Tool Suite was installed (normally “C:Program FilesDLP Composer Lite“). The wizard will find the file “DDP2000.inf“ and complete the installation. USB Support - Choosing the USB interface To select the USB communica
9、tions interface, choose “Preferences“ from the “Edit“ menu, click the “Communications“ page and choose “USB (DDP2000 Only)“. You can now use DLP Composer Lite to communicate with a DDP2000- based projector via USB using the Flash Loader and Projector Control tools. RD-JT92 and RD-JT91 Download Tool
10、Supply power to Projector. 1 2 Insert USB cable for download. 3 Click DLP Composer Lite Tool. USB cable Insert to Computer. Insert to Projector. RD-JT92 and RD-JT91 Download Tool Edit Preferences click 4 Appoint position that DDP2000.projector file is stored in Library item. 5 Establish by USB in Co
11、mmunications item.6 Flash Loader click In Project item In Flash Image File of Options item Skip Boot Loader Area (load all but the first 16 KB) Enter range of Inage Data to be updated (in Hex) Item uncheck box . 7 8 select Program (DDP2000_RefDesign_Flash.img) according to path stored program to upgrade S/W in Flash Image File of Options item. Start Download. 9 10 11 Click yes(Y) Downloading (1) RD-JT92 and RD-JT91 Download Tool Downloading (2) Download completed state Download complete. Extract USB and now Projector turn on . 12 13 RD-JT92 and RD-JT91 Download Tool
链接地址:https://www.31doc.com/p-2044062.html