《m一期光伏防雷接地(南河店).doc》由会员分享,可在线阅读,更多相关《m一期光伏防雷接地(南河店).doc(68页珍藏版)》请在三一文库上搜索。
1、烧结、TRT防雷接地施工方案编 制 人:审 核 人:批 准 人:江苏建兴建工集团有限公司三队目 录一、编制依据2二、工程概况2三、主要工程量统计2四、组织结构3五、施工准备3六、施工工艺4七、进度计划9八、材料、机具需求计划 10九、质量保证措施 11十、安全保证措施 11十一、文明施工措施 16一、 编制依据1、建筑物防雷设计规范GB50057-94(2002年版)2、建筑电气工程质量验收规范GB50343-20023、建筑物电子信息系统防雷技术规范GB50343-20094、防雷接地工程与等电位联结5、05D10标准图集6、电气装置安装工程接地装置施工及验收规范GB50169-20067、
2、接地网提前施工部分(60-B4631S-D0101)8、交流配电装置接地(60-B4631S-D0114)9、交流滤波器场接地(60-B4631S-D0115)10、换流变区域接地(60-B4631S-D0116)二、 工程概况本工程开关与光伏场区主地网以水平接地体为主,垂直接地极为辅。全站接地网图中点划线部分表示换流站本期需要上的主接地网三主要工程量统计:序号分项工程内容单位单位备注1土石方开挖m3130002水平接地敷设m220003垂直接地体根3114接地体焊接点处42005接地沟回填m313000四、 组织结构+项目部经理:项目总工:安 全:质 量:施工队长:五、 施工准备1、 技术准
3、备(1) 施工图纸和技术资料齐全。(2) 施工方案编制完毕并经审批。(3) 施工前应组织参与施工的人员熟悉图纸、方案,并进行安全、技术交底。2、 材料(1) 接地装置主材:扁钢、钢管等的规格型号符合设计要求,且全部为镀锌材料,产品有材质证明及产品出厂合格证。(2) 辅料有各种管箍等均为镀锌制品。(3) 电焊条、沥青漆等。3、 机具设备及劳动力准备:所有设备均在有效期内,焊工、电工均要有相应的资格证。(1) 手动工具:电工组合工具、手锤、钢锯、压力案子、台钳、铁锹、铁镐、挖机、夯机等。(2) 电动工具:电锤、冲击锤、电焊机、角磨机等。(3) 测试工具:小线、线坠、卷尺、水平尺等。(4) 劳动力:
4、根据现场实际情况拟安排焊工4人,小工8人,电工2人。4、 作业条件(1) 接地装置及均压带安装作业条件 敷设接地极及干线的沟槽开挖完毕。 随土建基础地板及结构施工过程中。(2) 室内接地干线作业条件 墙体施工完毕。 管道已预埋。(3) 屋顶避雷带安装作业条件 避雷带支架已经做完。 防雷引下线施工完毕。 具备调直场地和垂直运输条件。 需要脚手架处脚手架已搭设完毕。六、 施工工艺1、 工艺流程测量定位 基槽放线 基槽开挖接地体敷设接地体焊接焊接部位防腐自检合格监理部隐蔽验收接地沟回填电阻实测2、 操作方法 主接地网水平接地体选用-505热镀锌扁钢,敷设深度为1.2米。 垂直接地极采用50,L=2.
5、5m的热镀锌钢管。敷设深度为1.2m。 被截断的接地扁钢截面部分应用沥青漆进行防腐。 主网扁钢焊接的搭接长度为其宽度的二倍以上。 钢管接地极与水平接地扁钢用扁钢弯成的弧形卡子进行连接。先将扁钢弯成的弧形卡子与钢管接地极进行焊接,要求在其接触部位两侧进行焊接。再将扁钢弯成的弧形卡子与主网扁铁焊接。焊接为45的角焊缝,焊接高度为扁钢厚度。具体见图。 焊缝应平整、焊透、无间断,用沥青漆对焊接部位进行防腐处理。 接地体如遇电缆沟,则与电缆沟通长扁铁每15-30米做可靠连接,电缆沟内应做等电位连接;电缆沟内的支架上应设通长的接地铜排,截面为404mm。 均压带采用型号为304的扁钢,均压带的埋设深度为0
6、.7 米。图1 钢管接地极 挖沟:根据设计图要求,对接地体的线路进行测量放线,在此线路上挖掘深为1.2m、沟底宽为0.5m的沟,沟上部稍宽,底部渐窄,沟底如有石子应清除。 安装接地体(极):沟挖好后,应立即安装接地极和敷设接地扁钢,防止土方倒塌。先将接地极放在沟的中心线上,打入地中,一般采用手锤打入,一人扶接地极,一人用大锤敲打接地极顶部。为了防止将接地钢管打坏,可加一管帽套入接地管端。使用手锤敲打接地极时要平稳,锤击接地体正中,不得打偏,应与地面保持垂直,当接地体顶端距离地面1200mm时停止打入。也可用挖机慢慢垂直压入。 主地网方格网间距10-15m左右。 接地体敷设完后的回填土中不应夹有
7、石块和建筑垃圾等,在回填土时应用素土每300mm厚一层,进行夯实。 核验接地体:接地体连接完毕后,应及时进行隐检核验,接地体材质、位置、焊接质量等均应符合施工规范要求,然后方可进行回填,分层夯实。最后,将接地电阻摇测数值填写在隐检记录上。3、 房屋接地:综合楼、配电室和综合泵房在屋面女儿墙上设避雷带。屋面板受力钢筋与分布筋的焊点不少于300个(可以均布),除此之外的受力钢筋或分布筋接长、受力钢筋与分布筋交叉点可以采用绑扎,最终必须保证受力钢筋与分布钢筋整体连通,并与接地扁钢焊接。综合楼、配电室和综合泵房室内接地为沿室内地坪300mm高墙面进行敷设,在房屋的四角引4根接地扁钢与户外主接地网连接。
8、均采用505mm的扁钢。综合楼、配电室和综合泵房防雷引下线明敷设应符合下列规定:(1) 引下线扁钢截面采用50mm5mm。(2) 引下线应躲开建筑物的出入口和行人较易接触到的地点以免发生危险。(3)综合楼、配电室和综合泵房设两根引下线,房屋转角处对称位置布置。 4、 接地电阻的测量。 1 测量方法: (1) 如图2所示,沿被测接地极E,使电位探测针P和电流探测针C依直线彼此相距20m,插入地中,且电位探测针P要插于接地极E和电流探测针C之间。 (2) 用导线将E、P和C分别接于仪表上相应的端纽E、P、C上。 (3) 将仪表放置水平位置,检查零指示器的指针是否指于中心线上。若偏离中心线,可用零位
9、调整器将其调整指于中心线。 (4) 将“倍率标度”置于最大倍数,慢慢转动发电机的手柄,同时旋动“测量标度盘”,使零指示器和指针指于中心线。当零指示器指针接近平衡时,加快发电机手柄的转速,使其达到每分钟120转以上。调整“测量标度盘”,使指针指于中心线上。图2 接地电阻测量接线图 (5) 如果“测量标度盘”的读数小于1,应将“倍率标度”置于较小的倍数,再重新调整“倍率标度盘”,以得到正确的读数。 (6) 当指针完全平衡在中心线上以后,用“测量标度盘”的读数乘以倍率标度,即为所测的接地电阻阻值。 2 注意事项: 使用接地测量仪(接地摇表)时,应注意以下几个问题: (1) 当“零指示器”的灵敏度过高
10、时,可将电位探测针插入土壤中浅一些;若其灵敏度不够时,可沿电位探测针和电流探测针注水使之湿润。 (2) 测量时接地线路要与被保护的设备断开,以便得到准确的测量数据。 (3) 当接地极E和电流探测针C之间的距离大于20m,电位探测针P的位置插在EC之间的直线几米以外时,其测量的误差可以不计;但EC的距离小于20m时,则应将电位探测针P正确地插于EC直线中间。 (4) 当实测接地电阻达不到要求时,可首先采用增加接地极的方法来减小接地电阻。如仍不能满足要求,可根据实际情况采取下面一些措施: 置换电阻率较低的土壤; 接地极深埋; 人工处理,即在接地极周围土壤中加入降阻剂; 使用接地模块。 (5) 在使
11、用传统测量方法不便利的场所,可使用E2000型数字式接地电阻测试仪,它无需辅助线和探测针,只要将卡头在被测极上卡住,便可读出接地电阻值。七、施工进度计划:1、330kV设备支架区域主地网计划09.10.31完备注2、交流滤波器场主地网计划09.11.15完成3、换流变广场主地网计划09.11.20完4、直流场主地网图纸未到八、主要设备材料、施工机具需求计划:主要材料计划表编号名称型号及规范单位数量备注1水平均压带扁钢304米11000热镀锌2主网扁钢505米10000热镀锌3垂直接地体钢管504,L=2500mm根311热镀锌主要机具要求计划表编号名称单位数量1焊机台42电缆米4003电表块1
12、4锹把105挖锄把106大锤8镑把27翻斗车台28电源控制箱套29接地摇表块110切割机台111挖掘机台1九、质量保证措施:为确保工程质量优良, 本部工程需达到合格率100%, 优良率100%,主要质量保证措施如下:(1)严把质量关,对设计规范配备原材料进行检验,并将厂家提供的合格证,报送业主或监理工程师进行审查。(2)严格施工接地装置必须符合电力设备过电压保护设计规程、电力设备接地设计技术规程、电气装置安装工程施工及验收规范中的规定。(3)精心组织,在工程质量管理中,管理人员、技术人员、专业技工和施工人员,必须根据规程规定,组织学习。学习规范、提高自身素质。保证其工作的连续性及原有的专业操作
13、技能水平。(4)开展全面质量管理活动,强化各工序之间的衔接,坚持“三检制”。每道工序自检合格后,由专职质检员进行全面检查验收,然后由项目监理工程师进行验收、签认。(5)在整个施工过程中,开展形之有效的“三工”活动,做到班前讲话,班中检查,班后总结的管理方法,确保施工质量。十、施工安全保证措施:为确保安全,施工中应采取如下安全措施:(1)认真贯彻“安全第一,预防为主”的方针,全面落实南方电网公司电网建设工程施工安全和环境保护设施标准规定要求,加强安全教育和培训,提高安全意识,安全操作技能和自我保护意识。特殊工种,需持证上岗,做到不伤他人,不被他人伤害。把安全纳入计划管理目标。(2)建立健全组织机
14、构,严格实行岗位责任制。从项目部、施工队到班组设安全员,具体抓好作业安全,建立安全保证体系。把安全生产纳入各级领导的责任目标,实行严格考核。(3)建立建全安全管理制度,由质安部制定各项安全管理办法,开展一系例的安全教育;安全检查评比制度,班组安全活动制度。(4)重点抓好施工现场的安全工作;加强对机械设备和操作人员的管理,严禁违章作业,持证上岗,对机械设备进行一次全面检查和维护,定期对电缆进行检查与维护,焊机有良好的接地措施,电路敷设、漏电保护装置按有关规定操作,同时严格加强用电管理,由专职电工进行操作。杜绝各类安全事故。(5)加强对民技工的安全教育与管理。进入施工现场必须戴好安全帽,劳保着装。
15、危险源辨识及控制措施:序号作业活动危险点/危险源危害结果防 范 对 策1安全交底未经安全交底施工人身伤害、设备事故1.认真做好交底,有针对性地讲解危险点和预防措施,交底人与被交底人双方签字。2.认真执行公司、项目部、班组三级“任务、技术、安全、环境”要求的“四交”制度。3.对无安全措施或未经安全技术交底的施工项目,施工人员有权拒绝施工。2安全培训教育1.未经三级安全教育和考试,不懂安全操作规程2.意识水平低下,安全意识与技能掌握不够人身伤害、设备事故1.搞好安全教育与培训,提高人员安全素质。2.工程开工前,组织施工人员(包括民工)进行一次安全工作规程、规定、制度的培训学习与考试。3.施工人员换
16、工种时,进行相应的安全教育。4.实施新工艺新技术或使用新设备新材料时,进行有针对性的安全教育。5.临时招用当地民工施工前,由施工负责人讲解工作范围、安全注意事项和操作方法,宣讲安全作业票和安全监护制度。3施工电源布置施工电源设施布置不规范人身伤害、设备事故1.临时配电间、盘、箱布置合理,并全部检修完好合格,符合安全要求。2. 临时配电间、盘、箱统一着色,喷“有电危险”明显标志。3.电缆埋地敷设时,设直埋电缆标志牌,横过道路时,必须穿保护套管。4.各配电间、盘、箱全部配锁。5.便携式电源盘等,必须按要求装设漏电保护器。做好接保护。6.严禁私拉、乱接电源。4用电操作1.安装维护不当。2.操作不按规
17、定。人身伤害1.施工用电安装维护由合格电工担任。2.在操作及使用中,必须遵守电力建设安全工作规程中相关规定。5机械设备无管理制度人身伤害,设备事故制订制度责任不落实专人负责未按规定检修,带病运行按规定检查、维护、保养操作人员无证上岗加强培训,持证上岗违章操作加强监察,严禁违章指挥混乱统一指挥6土方开挖坍塌人身伤害、设备事故1.挖土前,根据挖土深度、土质、环境和地下水情况,做好边坡放坡和支护工作。2.挖土时应自上而下进行,严禁掏底的挖法。3.坑槽边1m内不得堆放材料、停放车辆、设备或堆土。坑边1m外堆土高度不超过1.5m,坑边有大型设备停放时或有作业时要采取加固措施。如发现坑槽裂缝、土质疏松,要
18、立即补救。4.雨天施工时要注意基坑周围的排水,以防积水冲垮护坡。5.采取措施预防挖孔、扩孔作业时塌孔。深孔内要做好通风、照明,以确保孔下人员安全。7机械开挖作业方式不符合要求人身伤害、设备事故1.采用大型机械挖土时,应有专人指挥。3.严禁人员进入斗内,不得利用挖斗递送物件。4.挖土机回转半径内,严禁其他各种作业。8施工机械操作人员个人防护用品不合要求人身伤害、设备事故根据施工机械使用要求,着装正确并使用个人防护用品精神状况不好施工机械使用人员应休息好,集中精力,密切关注施工机械状况对所用机械情况不熟悉由了解其性能并熟悉使用知识的人员操作施工机械,对重要施工机械应持证上岗误操作严格按施工机械性能
19、、规程、出厂说明书的规定使用9施工机械技术状况检验不严人身伤害、设备事故1.定期检验。2.使用前严格检查,严禁使用不合格的施工机械或机械带病运行。维修、日常维护不,保养不善1. 定期保养,施工机械应由专业人员维修。2. 做好日常维护保养,施工机械的各种监测仪表以及各种安全保护装置应齐全,完好。3. 在运行时不得进行检修或调整施工机械。4. 已到报废年限的施工机械经修理,技术状况满足使用要求,仍需继续使用的须按规定经有关部门检测合格,办理手续,并加强检测保养。10挖掘机转移、停放路面不平、沉陷或倾覆人身伤害、设备事故1. 履带式挖掘机转移工地,应用平板拖车运送。特殊情况需转移时,须卸去配重。2.
20、 作业后,停放在坚实、平坦的地方,铲斗落地,使提升绳松紧行当,臂杆降到4050位置。11挖掘机作业操作不规范人身伤害、设备事故1. 操作人员持证上岗。2. 挖掘作业时,应服从施工员的指挥。3. 待机身停稳再挖土。4. 挖掘半径范围之内不得站人。5. 操作人员离开驾驶室不论时间长短,必将铲斗落地。带故障运行设备事故1. 启动前,应全面检查机械运转部分、液压系统及电气装置等是否完好。2. 平时加强机械维护保养。3. 作业中,发现挖掘力突然变化、应停机检查。严禁在未查明原因前擅自调整分配阀压力。12手扶式碾压机打夯操作触电人身伤害1操作或传递导线人员必须戴绝缘手套,穿绝缘胶鞋。2检查电路应符合要求,
21、装漏电保护器,拉地(接零)良好,各传动部件均正常后,方可作业。3作业时,电缆线不可张拉过紧,应保证有34m的余量,递线人员应依照夯实路线随时调整,电缆线不得扭结和缠绕,作业中需移动电缆线时,应停机进行。4作业时,切断电源,卷好电缆,如有破损,应及时修理或更换。操作方法不当人身伤害、设备事故1不得夯实坚硬或软硬不一的地面,更不得夯打坚石或混有砖石碎块的杂土。2两台以上蛙夯机在同一工作面作业时,左右间距不得小于5m,前后间距不得小于10m。3操作时,不得用力过猛或按压手柄;转弯时不得用力过猛,严禁急转弯。4夯实填高土方时,应从边缘以内1015cm开始夯实23遍后,再夯实边缘。5在室内作业时,应防止
22、夯板或偏心块打在墙壁上。十一、文明施工措施:(1)把文明施工的目标具体化,具体落实到各个施工班组,杜绝野蛮施工行为,文明用语。(2)与其它施工单位保持良好关系,施工中遇到的问题和矛盾,应由项目部有关领导进行统一协调安排。(3)接受业主及监理的指导,对监理提出的问题及进行整改。(4)注意施工现场的整体形象,科学组织施工,爱护环境、美化环境、避免损坏已施工完的绿化地带。做到工完场清,保证现场施工的规范化,秩序化。(英文版 ) Two regulations promulgated for implementation is in the party in power for a long time
23、 and the rule of law conditions, the implementation of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two regulations supporting each other, the adhere to a positive a
24、dvocate, focusing on morality is of Party members and Party leading cadres can see, enough to get a high standard; around the party discipline, disciplinary ruler requirements, listed as negative list, focusing on vertical gauge, draw the party organizations and Party members do not touch the bottom
25、 line . Here, the main from four square face two party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental principles of the revision of laws and regulations in the party
26、; the third part introduces two party regulations modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. and revised the necessity and revised history of the CPC Central Committee the amendment to the
27、 Chinese Communist Party members and leading cadres honest politics several guidelines and column 1 by 2015 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole party, ideological consensus, draw historical experience, re
28、spect for the wisdom of our predecessors, which reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the partys leadership, to solve the masses of the people reflect a focus on the problem. The new revision of the and , reflects the party
29、s 18 and the eighth session of the third, the spirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the partys eighteen years comprehensive strictly practice. (a) revised two regulations of t
30、he party need of in based on revised, the promulgation and implementation of January 2010, to strengthen the construction of the contingent of leading cadres play an important role. But with the party to manage the party strictly administering the deepening, has not been able to fully meet the actua
31、l needs. Content is too complicated, eight prohibition, 52 are not allowed to hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy requirements; the third is banned terms and discipline law,
32、both with the party discipline, disciplinary regulations repeat and Criminal law and other laws and regulations repeat; the fourth is to clean the theme is not prominent, not for the existing problems, and is narrow, only needle of county-level leading cadres above. is in 1997 based on revision, in
33、December 2003 the promulgation and implementation, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive strictly administering the practice needs. One is Ji law, more
34、than half of the provisions and criminal law and other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage the authority of Party Constitution of misconduct lack necessary and serious r
35、esponsibility to pursue; third is the main discipline for the leading cadres, does not cover all Party members. Based on the above situation, need to and the two is likely to be more relevant regulations first amendment. By revising, really put the authority of Party discipline, the seriousness in t
36、he party tree and call up the majority of Party members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches great importance to two regulations revision . Xi Jinping, g
37、eneral books recorded in the Fifth Plenary Session of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations made clear instructions. According to the central deployment, the Central Commission for Discipline Inspection from 2014 under six months begin stu
38、dy two regulations revision. The Standing Committee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the direction, major issues of principle, path and target, respectively
39、 held a forum will listen to part of the province (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs Department The first party committee is mainly responsible for people, views of experts and scholars and grass
40、roots party organizations and Party members. Approved by the Central Committee of the Communist Party of China, on 7 September 2015, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomous regions, municipalities) Party, the central ministries an
41、d commissions, state ministries and commissions of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of extensive solicitation of opinions, careful study, attract
42、ing, formed a revised sent reviewers. In October 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 18, the Central Committee of the Communist Party of China fo
43、rmally issued two regulations. Can say, two laws amendment concentrated the wisdom of the whole party, embodies the party. Second, and revision of the basic principles of two party regulations revision work and implement the partys eighteen, ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General Secretary Xi Jinping important instructions on the revised and , highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the current, a long-term, a
链接地址:https://www.31doc.com/p-2047724.html