fn焊接工艺评定无损检测及试样试验报告资料02.doc
《fn焊接工艺评定无损检测及试样试验报告资料02.doc》由会员分享,可在线阅读,更多相关《fn焊接工艺评定无损检测及试样试验报告资料02.doc(57页珍藏版)》请在三一文库上搜索。
1、焊接工艺评定焊 接 工 艺 评 定中 十 冶 集 团 有 限 公 司二00六年二月十五日目 录序号编号焊接方法焊缝形式母材牌号焊材牌号1HP05-01电弧焊板对接Q235BJ4222HP05-02电弧焊板对接16MnRJ5073HP05-03电弧焊管板角接Q235B/20#J4224HP05-04电弧焊管板角接16MnR/20#J5075HP05-05氩弧焊管管对接20#/20#H08Mn2Si6HP05-06SMAW/SAW板对接Q235BJ422/H08A7HP05-07SMAW/SAW板对接16MnRJ507/H10Mn2attention to improving the qualit
2、y and efficiency of development and pay more attention to security and reform the peoples livelihood, more focus on maintaining social harmony and stability, and promote the development of township economy in a better and faster, create a new normal XX development and lay a more solid foundation for
3、 XX build a well-off society. Completed tasks this year, we must always pay special attention to the primary task of development. XX weak economic base, low levels of development, economic construction is the Center, we have to create conditions for faster economic development, accumulating more wea
4、lth, better peoples lives. Effort should be made to this years economic growth, revenue growth, people have maintained a high rate of income growth, GDP growth of more than 15 per cent respectively. Always grasp the fundamental impetus for reform. We are now no soldiers behind many indicators ranked
5、 in the bottom of the county from getting bigger. Only by going all out to hard work, hard work, innovation, reform does not adapt to institutional mechanisms, practices, it is possible to change the face of XX poor, into a well-off society together with people across the country. We want to break t
6、he old patterns of thinking, methods and organization of work, bravely and boldly into, making full use of all the advantages, comprehensive reforms, to make all its vitality for development impulse, let full play to all sources of wealth creation. Should always stability中十冶集团有限公司 - 55 -焊接工艺评定报告单位名称
7、:中国第十冶金建设公司 焊接工艺评定报告编号: HP05Y-1 焊接工艺指导书编号:NO.05-1 焊接方法:SMAW 机械化程度:(手工、半自动、自动) 焊缝宽度坡口两侧各加2mm,余高:02 mm。母材:材料标准:GB/T3274 钢号: Q235B 类、组别号:-1与类组别号-1相焊厚度: 9-18mm 直径: 其他: 焊后热处理:热处理厚度:() 保温时间(h): 保护气体:气体 配合比 流量(L/min)保护气体: 尾部保护气: 背面保护气: 填充金属:焊材标准:GB/T5117-95 焊材牌号:J422 焊材规格:2.5、3.2、4 焊缝金属厚度:18mm 其他: 电特性:电流种类
8、:交流 极性: 钨极尺寸: 焊接电流(A):2.5:75/85;3.2:110/130;4:150/180电弧电压(V):18-24 其他: 焊接位置:对接焊缝位置: 方向:(向上、向下)角焊缝位置: 方向:(向上、向下)技术措施:焊接速度(cm/min): 摆动或不摆动: 摆动参数: 多道焊或单道焊(每面): 多丝焊或单丝焊: 其他: 预热:预热温度():层间温度():其它:续表:拉伸试验 试验报告编号: HP 1 试样编号试样宽度(mm)试样厚度(mm)横载面积(mm2)断裂载荷(KN)抗拉强度(MPa)断裂部位和特性HP1-1406焊口外断HP1-2404焊口外断弯曲试验 试验报告编号:
9、 HP1 试样编号试样类型试样厚度(mm)弯心直径(mm)弯曲角度()试验结果HP1-1面弯48180合格HP1-2面弯48180合格HP1-3背弯48180合格HP1-4背弯48180合格冲击试验 试验报告编号: HP1 试样编号试样尺寸缺口类型缺口位置试验温度()冲击吸收力(J)备注HP1-1551010V焊缝区常温44实测值HP1-2551010V焊缝区常温46实测值HP1-3551010V焊缝区常温47实测值HP1-4551010V热影响区常温46实测值HP1-5551010V热影响区常温48实测值HP1-6551010V热影响区常温48实测值续表:金相检验(角焊缝)根部:(焊透、未焊
10、透) 焊缝:(熔合、未熔合) 焊缝、热影响区(有裂缝、无裂缝) 检验截面焊脚差(mm)无损检验RT: 试板焊缝经检验,评为级,合格 UT: MT: PT: 其他:焊缝外观检查合格 耐蚀堆焊金属化学成分(重量)CSiMnPSCrNiMoVTiNb分析表面或取样开始表面至熔合线的距离(mm): 附加说明:结论:本评定按JB4708-2000规定焊接试件,检验试样、测定性能、确认试验记录正确 评定结果: (合格、不合格) 焊工姓名高英保焊工代号JQ编制日期审核日期批准日期焊接工艺评定指导书单位名称:中国第十冶金建设公司 焊接工艺指导书编号:NO.05-1 日期: 2005.12.7 焊接工艺评定报告
11、编号: HP05Y-1 焊接方法: SMAW 机械化程度(手工、半自动、自动): 焊接接头: 简图:(接头形式、坡口形式与尺寸、焊道布置及顺序)坡口形式: V 衬垫(材料及规格): 其他: 母材:类别号: 组别号: 与类别号: 组别号: 相焊及标准号:GB/T3274 钢 号: Q235B 与标准号:GB/T3274 钢 号: Q235B 焊接 厚度范围:母材:对接焊缝: 9-18mm 角焊缝: 管子直径、壁厚范围:对接焊缝 直径不限 角焊缝: 不限 焊缝金属厚度范围: 对接焊缝 18 角焊缝: 不限 其他:焊接材料:焊材类别F1焊材标准GB/T5117-95填充金属尺寸2.5、3.2、4焊材
12、型号E4303焊材牌号(钢号)J422其他耐蚀堆焊金属化学成分()CSiMnPSCrNiMoVTiNb其他: 注:对每一个母材与焊接材料的组合均需分别填表。焊接工艺评定指导书焊接位置:对焊焊缝的位置: 焊接方向:(向上、向下) 角焊缝位置: 焊接方向:(向上、向下) 焊后预热处理:温度范围(): 保温时间(h): 预热:预热温度()(允许最低值): 预热温度()(允许最高值): 保持预热时间:加热方式:气体:气体种类 混合比 流量值(L/min)保护气: 尾部保护气: 背面保护气: 电特性:电流种类: 交 流 极性: 焊接电流范围(A): 75-180 电弧电压(V): 18-24 (按所指位
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- fn 焊接 工艺 评定 无损 检测 试样 试验报告 资料 02
链接地址:https://www.31doc.com/p-2121171.html