不同高铬镍奥氏体不锈钢电焊条焊缝组织性能对比分析.doc
《不同高铬镍奥氏体不锈钢电焊条焊缝组织性能对比分析.doc》由会员分享,可在线阅读,更多相关《不同高铬镍奥氏体不锈钢电焊条焊缝组织性能对比分析.doc(10页珍藏版)》请在三一文库上搜索。
1、-范文最新推荐- 不同高铬镍奥氏体不锈钢电焊条焊缝组织性能对比分析 摘要本论文针对A402、A412、A407奥氏体不锈钢焊条焊接过程中的开裂现象,开展了对奥氏体不锈钢焊接性的研究。通过对奥氏体不锈钢焊条全熔焊缝金属的力学性能测试,化学成分测量,铁素体含量测量,微观组织的分析,尝试探讨奥氏体不锈钢焊接过程中出现的开裂问题。结果表明:采用手工电弧焊使用A402、A407、A412对奥氏体不锈钢焊接,发现铬镍当量比例,焊缝金属结晶模式,铁素体结晶形态以及枝晶大小程度是影响焊缝金属塑韧性的主要因素。关键词:手工电弧焊 奥氏体不锈钢焊条 焊缝塑韧性 微观分析9023毕业设计说明书(论文)外文摘要Tit
2、le: Deferent high chromium-nickel austenitic stainless steel welding rod’s comparative analysis of the weld microstructure and properties.AbstractDue to the cracking phenomenon in the welding process of A402, A412, A407 austenitic stainless steel electrode, research on the weld ability of aust
3、enitic stainless steel is carried out. By the mechanical properties of deposited metal of austenitic stainless steel electrode financial test, the chemical composition measurement, ferrite content measurement, microstructure analysis, to solve the problem of cracking in the welding process of austen
4、itic stainless steel.The results showed that: Using the A402, A407, A412 austenitic stainless steel electrode for the manual metal arc welding and found that the proportion of chrome-nickel equivalent ,weld metal crystallization mode, ferrite crystal morphology and the degree of dendrite size is the
5、 main factor to affect the plasticity and toughness of weld metal.Keywords: Manual arc weldingAustenitic stainless steel electrodeWeld plastic toughnessMicroscopic analysis目次1.绪论1 1.1奥氏体不锈钢焊接方法奥氏体不锈钢焊接方法多样,常见的奥氏体不锈钢的焊接方法有以下几种34。1 焊条电弧焊焊接工艺要点:奥氏体不锈钢焊接环境温度一般不应低于0 ,否则,熔化情况不好,也容易产生裂纹,但不得对工件预热。为防止产生晶间腐蚀和
6、热裂纹,应采用快速焊、窄焊道。为防止药皮发红及母材过热,焊接电流不宜过大,一般比相同直径的碳钢焊条小20左右。焊接时尽量采用平焊位置,焊条角度要正确,运条要稳,电弧不宜过长,焊条最好不作或稍作横向摆动。一次焊成的焊缝不宜过宽,一般不应超过焊条直径的3倍。多层焊时,每焊一层后应彻底清渣,并仔细检查有无缺陷,在确定无缺陷时才能焊下一层。为防止晶问腐蚀应严格控制层间温度,待上一层焊道冷却至60 以下时再焊下一层焊道。奥氏体不锈钢一般不进行焊后热处理,且焊后变形不能用火焰加热矫正,只能用其他方法防止和消除变形。2 钨极氩弧焊钨极氲弧焊焊接线能量很低。特别适合焊接对过热敏感的各种奥氏体钢。这种方法的主要
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 不同 高铬镍 奥氏体 不锈钢 焊条 焊缝 组织 性能 对比 分析
链接地址:https://www.31doc.com/p-2165094.html