《某某公司产品确认规格书.doc》由会员分享,可在线阅读,更多相关《某某公司产品确认规格书.doc(14页珍藏版)》请在三一文库上搜索。
1、XX公司产 品 规 格 书SPECIFICATION FOR APPROVAL产品型号GIE0118B版本A产品结构5” G+G产品类型电容式触摸屏制作人(Prepared by)设计部审核(Checked by)品管部审核(Checked by)总经办批准 (Approved by)请客户仔细阅读规格书中的各项内容,当对规格书内各项内容表示认可时;请在下面客户确认项中签字(此规格书为一式两份)。Please read the following carefully the contents of the customer, the customer said after the signin
2、g of the cover on the confirmation of the customer to acknowledge the contents. 客户确认确认人 (Confirmed by)设计部审核 (Checked by)品管部审核 (Checked by)批准 (Approved by)变更记录表序号版本号修改人修改内容概要批准生效日期1A陈小艳初次发行2345目 录1 工程图 Engineering Drawing 2 产品结构 Construction3 机械特性 Mechanical Characteristics4 电气特性 Electrical Character
3、istics5 光学特性 Optical Characteristics6 使用环境 Processing Environment7 引脚定义 PIN Assignment8 驱动IC Controller IC9 机械测试 Mechanical Test10 寿命测试 Life Test11 环境测试 Environment Test12 检验标准 Inspection Standard13 包装及运输 Package&Transport14 注意事项 Attention15 质量保证 Guarantee1 工程图 Engineering Drawing2产品结构 Construction结
4、构Construction所用材料Materials Used注释Comment镜片COVER LENS玻璃GLASS厚度:0.70mmThickness:0.70mm透明胶OCA粘胶Adhesive厚度:0.175 mmThickness:0.175mmITO SensorITO Sensor厚度:0.55 mmThickness:0.55 mm3 机械特性 Mechanical Characteristics项目Item描述Description单位Unit外形尺寸Outside Dimension1400.1 81.80.1 mm可视区 View Area113.1271.51mm2动作
5、区 Active Area107.664.8mm2产品厚度Thickness1.450.1mm输入方式 Input Method手指或者导电笔触Finger Or Conductive Pen 表面硬度 Hardness Of Surface表面防刮伤 Hard Surface : 6H JIS K 5400 精确度 Accuracy+/-1mm10mmmm支持操作Support Operation 指Finger2指屏体通道数Channel17*10分辨率Resolution480*800接口定义InterfaceI2C支持操作系统Supported Operating SystemsAnd
6、roid2.0-2.3,Window7 4 电气特性 Electrical Characteristics项目Item描述Description单位Unit工作电压 Operating VoltageDC 1.8 VV绝缘阻抗 Insulation Resistance20M At DC 25VM绝缘稳定性 Insulation Ability60sec. At DC 25Vsec响应时间Chatting Times5msms5 光学特性 Optical Characteristics项目Item描述Description全光透光率 Total Transmittance82% JISK710
7、5雾度Total Haze 3% JISK71056 使用环境 Processing Environment项目Item描述Description工作温度 Operating Temperature-10+60工作湿度 Operating Humidity90%RH储存温度 Storage Temperature-20+70储存湿度 Storage Humidity90%RH7 引脚定义 PIN Assignment引脚PIN信号Signal描述Description1VDDSupply Voltage2SCLI2C Serial Clock Input.3SDAI2C Serial Data
8、 Input And Output.4INTAn interrupt signal to inform the host processor that touch data is ready for read5WAKE6GNDGround8 驱动IC Controller IC9 机械测试 Mechanical Test1 钢球跌落测试Ball Drop Test(1) 作业环境:温度:223、湿度:6010RH、Level:等级1000Operating Environment:Temperature:223、Humidity:6010RH、Level : Class1000(2) 测试方法
9、:用直径为9mm钢球从30cm高度跌落产品中心,产品不会破裂为合格。Test Method: With a diameter of 9mm ball falling from 30cm height to Product Center, the product will not break as qualified. 2 静压测试Static Press Test (1) 作业环境:温度:223、湿度:6010RH、Level:等级1000 Operating Environment:Temperature:223、Humidity:6010RH、Level:Class1000 (2) 测试方
10、法:在产品表面放置一个直径为12.7mm橡胶头,产品功能无问题,无破损。Test Method: Product placed on the surface with a diameter of 12.7mm rubber head, Function is ok, no damage. 3 FPC压合测试FPC Bending Test (1) 作业环境:温度:223、湿度:6010RH、Level:等级1000 Operating Environment:Temperature:223、Humidity:6010RH、Level:Class1000 (2) 测试方法:产品测试后满足电气性能
11、。Test Method: Meet electrical spec after testing.1.测试角度Bending Degree:135;2.测试半径Bending Radius: R1.0 mm;3.测试次数Bending Times: 50 Times;4.测试重量Load: 500g. 4 FPC插拔测试FPC Insert/Pull Out Test: (1) 作业环境:温度:223、湿度:6010RH、 Level:等级1000 Operating Environment:Temperature:223、Humidity:6010RH、Level:Class1000(2)
12、测试方法:Test Method: A.测试前确认电性特性符合规格; Before Test: Electrical Characteristic Test is OK. B.测试步骤:开卡锁连接器插入FPC锁住FPC开卡锁连接器插入FPC锁住FPC,重复10次; Test Circle: Connector Unlock FPC Insert Connector Lock Connector Unlock FPC Pull Out Connector Lock, cycle 10 Times; C.测试后再次确认电性特性符合规格. After Test: Electrical Charact
13、eristic Test is OK;10 寿命测试 Life Test(1)作业环境:温度:223、湿度:6010RH、 Level:等级1000 Operating Environment:Temperature:223、Humidity:6010RH、Level:Class1000项目Item规格Specification条件Condition打点寿命 Input Life250g3500万次35,000,000 Times功能OK,外观轻微划伤OK。 The function is ok。笔写寿命 Notes Life250g10万次100,000 Times功能OK,外观轻微划伤OK
14、。 The function is ok。11 环境测试 Environment Test(1)高温测试 High temperature:+80,120 hr.(2)低温测试 Low temperature:-20,120 hr.(3)高温高湿测试 High temp./high humidity test:60&90%RH 120 hr.(4)高低温测试 High Low temperature test:-20 30min/+70 30min, 60%RH 24hr,this is a Cycle, continued 24hr test. (Including heating and
15、cooling of 30 minutes) 将产品从测试机内取出,在室温放置24小时后才能进行测试,功能无异常。Remove the product from the testing machine, at room temperature for 24 hours before testing, function is OK.12 检验标准 Inspection Standard1 检验条件Inspection conditions: 1.1 检查距离:距离产品250-300mmInspection distance: Inspect 250-300 mm away from the sa
16、mple.1.2 检查角度:45度,6点钟方向(所有的不良项目在此方向和角度需要被检查出来)。 Inspection angle: 45 degrees in 6 oclock direction (all defects in viewing area should be inspected from this direction),Rotate 30 about the vertical axis1.3 环境温度为:20-30度Temperature: 255 C1.4 光源高度:D65 800-1200 LuxLight source: D65 1000 Lux +/- 20%2 检验项
17、目Inspection Items:项目Items图片Picture 类型Type标准 Standard判定Judgment备注Remarks玻璃破损The Glass is damaged拐角破损Its damaged to turn CapeMaX1.5mm合格Accept在不影响功能的前提下Without affecting the function of the premiseY1.5mm合格AcceptZ1/2T 合格Accept除转角以外任何范围的破损In addition to turning Cape any breakage of scope cornerMiX2.0mm合格
18、Accept在不影响功能的前提下Without affecting the function of the premiseMaY2.0mm合格AcceptZ1/2T 合格Accept玻璃破裂Broken GlassCr产品任何部位存在破裂Product any part exists broken不合格Failure点状物 (包括白点与黑点等) Spot (includes white and black spots)MaD0.15mm 合格 Accept0.15D0.3mm 2( 25mm separation); 0.3D0.35mm, 1个 允许 AllowCrD0.35mm 不合格Fa
19、ilure刮伤ScratchMaW0.05mm合格 Accept 0.05W0.1 ,L3mm 1个,相距大于25mm 。 允许 AllowCrW0.1mm 不合格Failure线性物Linear MaterialMi W0.05mm合格 AcceptMa0.05W0.1 ,L2mm 2个,相距大于25mm 。 允许 AllowCrW0.1mm 不合格Failure气泡Ma0.15D0.3mm ,3个相距25mm 0.30D0.35mm,1个允许 AllowD0.15mm 合格 AcceptCrD0.35mm 不合格Failure内污(产品内部)Inside Dirty(Product inn
20、er part)Ma呈圆形状Cylindrical shape不合格Failure于灯光下目视可视区内内污直径大小超出点标准范围的块状明显污迹Visual areas in the visual light pollution within the diameter of the block beyond the obvious point of the standard range of stains长条状Strip集中状Concentrated form斜纹状Twill-like水纹状(含手纹)Watermark-like (with hand lines)保护膜及表面脏污Protecti
21、ve Film And Surface DirtMi保护膜贴于产品两面,边缘与产品对齐。保护膜超出产品边缘2mm。Protective film affixed to the product sides, edges and product alignment. Protective film products beyond the edge of 2mm.合格 AcceptMa产品撕起保护膜后,目视检查TP表面有脏印。Tear the protective film products, the visual inspection TP surface dirty Indian.不合格Fail
22、ure13 包装及运输 Package and Transport 1 包装 Package 不可有脏东西附着,使用泡沫盒材质包装。Can not have dirt attached, use foam box packing material. 2 输送Transport 避免产品直接暴露在阳光直射或高温高湿的环境下运输。Avoid direct exposure to sunlight or high temperatures and humidity environment transport.14 注意事项 Attention项目Project注意事项Notes储藏Store(1)
23、按照本规格书中保存温度范围要求储藏产品。 In accordance with the specifications required storage temperature range of book preservation products.(2) 储藏时请保证产品包装完好。 Please ensure the product packaging when stored in good condition.(3) 避免阳光直射产品。 Avoid direct sunlight product.(4)尽量避免产品接触水、有机溶剂、酸性物质和硫酸化合物等。 To avoid product
24、contact with water, organic solvents, acid and sulfuric acid compounds. 拆包装Unpacking(1) 请勿通过抓住 FPC 来取放产品。 Do not grasp the FPC to take place through the product. (2)按照包装箱上的上/下标记方向打开产品包装。 According to the box on the Over / under Mark the direction of opening the product packaging. 操作Operating(1) 输入时应
25、使用手指或专用笔。 Input should use your fingers or pens. (2) 不可用力拉扯 FPC,以免造成产品内部电气连接不良;不可扭曲和弯折 FPC 输出端,以免造成 FPC 与控制器的连接不良。 Can not pull hard FPC, to avoid bad electrical connection inside the product; not twisted and bent FPC output, so as to avoid adverse FPC connection to the controller. (3) 不可弯折和分解本品。 Ca
26、n not bend and break the product.(4)不要在产品的动作区域滴上水滴,以免引起误操作。 Do not drop the product of the action on the drop zone, in order to avoid misuse. 上机Installed (1) 请勿在触摸屏上施加过大压力而造成产品损伤。 Does not touch too much pressure is applied to the product cause injury.(2)整机设计时,请避免损伤 FPC 及呈锐角状弯折 FPC。 Machine design;
27、avoid injury and acute angle-shaped bend FPC FPC. (3)请勿在 FPC 与屏连接部施加过大压力,导致屏体内部电气连接不稳定。 Do not connect the FPC and the department of screen put too much pressure, leading to screen the internal electrical connection is unstable. (4)组装时避免工具损伤产品。 Assembly of the product to avoid tool damage. (5)装机中尽量避
28、免静电产生。 Try to avoid static electricity installed.15 质量保证 Guarantee 1 本条款适用于深圳北泰显示技术有限公司生产的所有产品。 The provision applies to all the products made by Shenzhen Beitai Display Co, Ltd. 2 北泰公司对条款适用内的产品于购买日起,提供壹年(1年)的质量保证期,如在质量保证期内是我司责任的不良品,我司将负责返修或更换。 Beitai Company supplies quality guarantee of 1 year sin
29、ce the day of product purchase, and we would either repair or replace the bad products if they are unqualified from the beginning. 3 以下情况不在我司保证范围之内,我司不给予返修或更换。具体如下: Our company would not repair or replace the products of the following conditions, which is out of guarantee scope; 3.1产品交付客户后,因跌落或撞击或不当
30、操作造成的不良品; Products damaged by falling, impacting or improper operation after delivering to customers; 3.2因为自然灾害造成的不良品;Products damaged by natural disaster; 3.3在未经我司同意之前,客户私自进行再加工处理的产品;Products processed by customers without any permission of our company; 3.4客户未按注意事项作业而造成的不良品。 Products damaged by cus
31、tomers whoever conducts the operation without complying with the instructions. 4 本确认书经客户承认后,客户不得有所变更,如需变更,需双方友好协商好重新出确认书认可,否则一切损失由贵公司负责。 The customer should not change the Confirmation Document after approved by the customer. If the change is necessary, the two parties should make a new Confirmation Document for approval through negotiation friendly; otherwise, any caused loss should be beard by the company. 2012-1-09 GIE0118B Page 14 of 14
链接地址:https://www.31doc.com/p-2552771.html