电路板讲解.ppt
《电路板讲解.ppt》由会员分享,可在线阅读,更多相关《电路板讲解.ppt(49页珍藏版)》请在三一文库上搜索。
1、集成印刷电路板,集成电路板与线路的 相互连接,电源配给集成电路板,电源分配电路板,相位检示,POWER SUPPLY PCB,微处理器集成电路板,地址总线(I/O寻址),数据信息,键盘输入 数据交流,3,4,-,3,0,9,2,微处理器 芯片,EPROM 可写读芯片,3 MB 恆忆内存( FLASH RAM),芯片写入 保护开关,日期 / 时间 芯片,地址总线(I/O寻址),数据信息,键盘输入 数据交流,3.3 伏电池,电池维持记忆内存 1MB或16 MB,COLDFIRE 266 MHZ 微处理器芯片,64 MB 随机内存,辅设端口,COLDFIRE 微处理器主板,8 MB 恆忆内存( FL
2、ASH RAM),COLDFIRE 微处理器集成电路板,Coldfire I,Coldfire II,Coldfire II,RS-232 端 口 1&2,芯片写入 保护开关,USB 端 口,视 频 图 象 端 口,视 频 图 象 微处理器芯片,地址总线(I/O寻址),数据信息,键盘输入 数据交流,3.3 伏电池,电池维持记忆内存 1MB或16 MB,COLDFIRE 266 MHZ 微处理器芯片,64 MB 随机内存,辅设端口,8 MB 恆忆内存( FLASH RAM),特点,料号 93-32-4400 (CF I) 料号 93-32-4410 (CFII) 266MHZ 速度 嵌入式复合(
3、二合一)微处理器 64 MB DRAM 内存 14xx 软件 (取代 F 或 N 版本) CFI 15xx 软件 CFII,HOLD POWER ON (KEY) HOLD,PRGRM CONVRS,(KEY),视频图象集成电路板,图象视频板 (配备软驱),图象视频板 (配备软驱/ZIP/以太网 ),液晶显示屏/硬盘/网卡/ZIP 集成电路板,注意: 必须具备液晶显示屏及安载12.05或以上软件的哈斯机床才适用于这些配置.,图象视频板 配备硬盘/U盘/以太网,注意: (配USB)必须具备液晶显示屏及安载12.06或以上软件的哈斯机床才适用于这些配置.,串联键盘信息联接卡,手动进给 (操控台键盘
4、和手轮),电压输入,键盘 信息连接,主机负荷表信息,键盘信息,(To MOCON) P10,(来自 低压电源 供给系统 ),(往微处理器) J4,(来自 运行与进给截止开关),(来自 键盘),(往喇叭),(+12伏直流电),(来自电机矢驱集成电路板),手动进给,(遥控手轮),操控台内部,115伏交流电 来自 电控柜供电卡板,蜂鸣器,软驱,串联键盘信息联接卡,液晶显示屏,数据信息(来自图象视频板),低压供电卡板,液晶显示屏上所示的装置管理,HARD DRIVE,O00300,记忆储存,软驱,网络共享 (服务器上的共享 文件夹),ZIP,硬盘,帮助,资料来源,按F1-帮助,程序总数尚存空间,资料储
5、存目的地,程序表列,帮助目录-按 左光标 及 END 键,现行操控模式,输入/输出集成电路板 ( I/O 集成电路板),I/O PCB,I/OPCB-T RELEASE NOTES Rev. A Production Release. Rev. B Added adjustment for LCC chipc. Rev. C Corrected typos in steps 10 and 12, ECO-13076. Rev. D Changed 1-phase belt style to 500 in step 7. DESCRIPTION IOPCB-T is designed for n
6、ew machines only. It is completely interchangeable and backward compatible with IO-S only. It can only be used in brushless controls with a Haas vector drive. This board also requires the psup-g or later. Since the IO-T is based on IO-S, the changes listed below are from IO-S to IO-T. INTERCHANGE AB
7、ILITY IO-T is completely interchangeable with IO-S. When replacing an IO-S with an IO-T, follow the installation procedures below. IO-T is stuffed as three parts. 32-3083T is for the Haas SMTC. 32-3088T is a partially stuffed board for minimill, minilathe, tool room mill. 32-3080T is for all other c
8、ontrols. INSTALLATION PROCEDURES Power Off: 1. Review all safety text printed in the pcb silkscreen. 2. Jumper any unused E-Stop input connectors (P6 or P7). Jumper second door switch input (P9) if unused. Jumper second remote unclamp input (P20) if unused. See attached drawing for jumper placement.
9、 3. Verify that connector P48 is jumpered. 4. Verify that no jumper is installed at J9. This header is used for testing only. 5. Set tc current limit jumper correctly. Set jumper to 10A position for HS and Haas SMTC. Set jumper to 5A position for all others. 6. Set ground fault jumper (J1) to 0.75A
10、position. 7. Adjust chipc over current (R119 & R122) to 3-5K for single phase motors. (Adjust to 1K for three phase motors.) (Adjust to 500 for 1-phase, belt style, lathe chip conveyor.) 8. For all SL and most VF, install tc jumper cable (33-0809, supplied) at P57. Remove only if there is a cable th
11、at will plug in here instead. 9. Verify that a 10A ultra-fast fuse is installed at FU1 as shown on silkscreen. A spare fuse is included at FU2 that can be used in the event of a short circuit. Power On: 10. Verify that parameter 209, “MCD RLY BRD”, is set to a “1”. The “Relay Bank Select” parameter
12、352 should be set to either a 1, 2 or 3 depending on whether additional M-code relay boards are present. 11. Verify that parameter 57, “PH LOSS DET”, is set to a “0”. 12. Measure ground fault voltage (at TP2 to TP3). The value should be 0.065-0.085V. Operate tool changer several times. If a ground f
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 电路板 讲解
链接地址:https://www.31doc.com/p-2590281.html