RYL718-J型自动换梭织机中英文.doc
《RYL718-J型自动换梭织机中英文.doc》由会员分享,可在线阅读,更多相关《RYL718-J型自动换梭织机中英文.doc(33页珍藏版)》请在三一文库上搜索。
1、RYL718-J型自动换梭织机产品说明书中国 盐城市荣意来纺机有限公司二0一四年一、产品规格 Product specifications 1、产品用途及使用范围 The purpose and scope of use2、技术特征 Technical feature3、传动机构 Drive mechanism4、主要组成部分及其规格The main part and its specifications5、附件Accessory二、机器各主要组成部分说明 Machines main parts introduction1、机架 Base Frame2、开口机构Shedding mechani
2、sm3、换梭机构Shuttle changing mechanism 4、缓冲装置及缓冲保护器Buffer device and buffer protector5、打纬机构Beating-up mechanism6、经纱架保护装置The warp holder protection device7、卷取机构 Winding mechanism8、伸幅装置和布边毛纱剪断装置Stretching device and edge yarn cutting device9、送经机构Let-off mechanism10、断经自停装置Warp stop motions11、断纬自停装置Weft sto
3、p motions12、自动换梭装置Automatic shuttle changing device13、换梭安全装置Shuttle changing safety device14、无梭侧梭自停装置Shuttleless side spindle automatic stop device15、探针换梭诱导装置Probe induced shuttle changing device16、起动制动装置Starting braking device三、机器的加油lubricants to the machine四、技术安全要求Technical Safety requirements一、产品
4、规格 Product specifications 1、产品用途和使用范围 The purpose and scope of product本机主要适用于织造中支纱被单织物,织物工艺特征:平纹织特组织,斜纹织物组织。This machine is mainly suitable for weaving yarn in the bed sheet fabric, fabric craft characteristics: flat fabric organization, twill fabric.2、技术特征 Technical feature(1)型式下打手,不停车自动换梭式 Type -
5、the thugs, without a stop automatic shuttle changing type(2)手向分左手车和右手车The hand directionleft hand and right hand models(3)穿筘幅度1350mmReeding amplitude1350mm(4)曲轴转数斜纹154168r/minThe crankshaft revolutionstwill 154168r/min(5)胸樑高度838mm Breast beam height838mm(6)梭箱数11Shuttle Box number11(7)钢筘与走梭板间夹角8630An
6、gle between Reed and the shuttle plate8630(8)梭库容梭量10只 Capacity of the shuttle box10 pieces(9)经轴盘片直径550mm Beam disc diameter550mm (10)经轴盘片间距1380mmDistance between Beam disc1380mm(11)捲布棍满卷直径280mmMax cloth roller diameter280mm(12)电动机转速960r/minMotor speed960r/min(13)电动机功率1.5kwMotor power1.5kw(14)电气开关按钮开
7、关Electric switchesbutton switch(15)机器外形尺寸宽1900mm,高1670mm,长3000mmOverall dimensionsW 1900mm,H1670mm,L3000mm(16)机器重量1800kgMachine weight1800kg3、传动机构Drive mechanism(1)传动方式单马达三角皮带传动Driving modesingle motor triangle belt transmission(2)操纵方式单侧按钮开关Manipulation wayone button switch(3)制动形式电磁刹车模式Form of braki
8、ngelectromagnetic brake mode(4)踏盘轴和曲柄轴速比1:2Stepped shaft and crank shaft speed ratio1:2(5)倒车形式按钮控制Reverse form button control4、主要组成部分及规格Main components and specifications (1)送经机构Let-off mechanism a、形式积极式自动外送经、自动调整经纱张力Form - positive type automatic let-off, automatically adjust the warp tension b、经轴轴
9、心直径110mm(无缝钢管)Beam axis diameter 110 mm (seamless steel tube) 经轴盘片直径550mm Beam disc diameter550mm(2)断经停车装置 Warp stop devicea、形式导电式 Formconductive typeb、停经片杆列数4列6列Drop needle bar columns 4-6 columns(3)开口机构 Shedding mechanisma、形式多臂式拉综开口Form - dobby type heddle openingsb、综框数2片14片(木横头铝合金综框)Heald frame n
10、umber - 2-14 pieces (wooden cross pein aluminum alloy heald frame)(4)投梭机构 Pick institutionsa、形式下投梭Form - pickb、梭子尺寸长343mm宽32mm高35mm(分左右手)Shuttle sizeL 343mmW 32mmH 35mm (left and right hand)c、皮结型式活动皮结 picker typeactive pickerd、皮结尺寸(长7105mm宽132mm高35mm(分左右手)Picker size (L 7105mmW 132mmH 35mm (left and
11、 right hand)(5)打纬机构Beating-up mechanisma、形式曲柄轴牵手打纬 Beating-up formthe crank shaft in handb、曲轴直径40mmDia. of crank-shaft40mmc、曲臂半径(R)82mm The crank arm radius(R)82mmd、牵手形式轴瓦式牵手Hand formShell in hande、牵手长度289mmConnecting rod length289mmf、牵手栓直径25mmConnecting rod bolt diameter289mmg、牵手中心到揺轴中心距离685mmHand
12、to shaft center distance685mmh、揺轴形式整根Shaft formthe whole rooti、揺轴直径38mmShaft dia. 38mmj、筘座形式铁木结构The reed formiron and woodl、走梭板长度1423mm Go shuttle plate length1423mmm、梭箱底板长度开关侧580mm,梭库侧600mmBox floor lengthswitch side 580 mm, spindle library side 600 mm(6)经纱保护装置Warpprotector motiona、形式游筘式Formloose r
13、eed type(7)捲取机构 Rolling mechanism a、形式七齿式间歇捲取Seven tooth formintermittent rollb、纬密范围1046根/英寸The weft density range10-46 root/inchc、刺毛棍直径127mm(无缝钢管)licker-in roller diameter127 mm (seamless steel tube) d、导布辊直径34mm(无缝钢管)Cloth guide roller34 mm diameter (seamless steel tube)e、捲布辊直径85mmcloth roller diam
14、eter85mm(8)伸幅装置 Stretch devicea、形式单排铜刺环辊式Form - single copper ring rollerb、只数左右各一组 Quantitya group at each left and right sidec、剪纬缒筘座撞动使剪缒作用。 An opening of weftThe reed hit move to cut into effect(9)断纬自停装置 Weft stop motionsa、形式点啄式探纬 FormPoint pecked out weft b、捲取退捲装置有Roll back roll deviceYes(10)纬纱补给
15、装置 Weft supplying motiona、形式自动换梭式 FormAutomatic shuttle changing typeb、梭库垂直单列式Shuttle box-vertical single-row c、梭库容梭量10只 Shuttle quantity in shuttle boxten pieces d、换梭诱导装置采用探针换梭诱导装置 Shuttle changing induction device-apply probe shuttle changing induction devicee、换梭安全装置有,如换梭运动发生故障时,能即时停车,避免机件损坏。Shutt
16、le changing safety deviceyes, Such as if a shuttle changing fails, machine can stop instantly so as to avoid damage to the parts. f、无梭、侧梭停车装置有,如梭库内无梭子或梭子位置侧放时,能立即自动停车。 Shuttleless, side shuttle stopping device-yes, the machine can instantly stop if there is no shuttle in shuttle magazine or shuttle
17、is put sidelong.g、防止残纬织入装置有,可避免毛边,双纬等疵点,提高织物质量。 Residual weft weaves prevention device-yes, which can avoid rough selvedge, double weft etc defects, so as to improve fabric quality.5、附件 accessory(1)随机供应件a、地脚螺钉一组b、捲取标准、变换齿轮各1只(1) Parts with loomsa, ground screw-one groupb, roll standard and changing
18、gear-one piece each(2)不随机供应件:由客户自理a、梭子(长)343mm(宽)44.5mm (高)33.5mmb、纬管总长180mm(头部直径27mm)c、钢筘总长1400mm 高120mmd、综丝330mm(2) Parts not together with loom: customer choose a、shuttle(long)343mm(wide)44.5mm (high)33.5mmb、weft pirntotal length 180mm(head dia27mm)c、steel reedtotal length 1400mm height 120mmd、ha
19、rness wire330mm(3)下列各件是否供应,根据合同办理a、马达型号:F03-5三根型,转数960r/min,功率1.5KWb、三角皮带A2235 (3) Supply of the following parts is as per the contract a、motormodel:F03-5 three pieces model,RPM960r/min,power1.5KWb、triangle beltA22351、机架 loom frameA 机构作用说明 机架主要由左墙板、右墙板和连接两块墙板之间的前横梁、后横梁、中间横梁、胸梁、和前后撑挡组成,用左小墙板和右小墙板各一块,
20、上横梁装于小墙板上方,为了使机架稳固小墙板间,并从上支撑、小撑挡连接之。机架间的连接螺栓必须坚固,如机架安装不当时,机器运转时各轴中心容易发生走动,亦不可能使织机轻快灵活的运转。本机整个机架座按放在垫木上,再用地脚螺栓和地基坚固,以防震动。 A: function instructionLoom frame is mainly composed of the left wallboard, right wallboard, the front beam, rear beams, and middle beam, breast beam, front and back spreader conn
21、ecting two wallboards, one small left wallboard and right wallboard, upper beam is installed at the top of small wallboard so as to fix loom between small wallboard and connect it through upper beam and small spreader. Connecting bolts between loom frames must be firm, if improper installation of lo
22、om frame, the beams are prone to move while loom running so the loom could not operate smoothly. The entire frame of this machine is installed on stow-wood, use foundation bolt and foundation to fix again in case of vibration. B 安装与调试 installation and commissioning (1)墙板竖立后,放置前横梁定规和后横梁定规于车脚上,再安装前横梁和
23、后横梁,其左右两端应与墙板外侧边缘平齐。 After wallboard erected, put front and rear beams frame on the loom foot, then install front and rear beams, both ends of beams should be parallel with outer edge of wallboard.(2)装上胸梁,使与墙板外侧边缘相互平齐,并在装梭库侧处查看是否水平。 (2)Fit on breast beam, make it parallel with outer edge of wallboar
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- RYL718 自动 织机 中英文
链接地址:https://www.31doc.com/p-2726603.html