《Switch命令大全.doc》由会员分享,可在线阅读,更多相关《Switch命令大全.doc(12页珍藏版)》请在三一文库上搜索。
1、Cisco认证知识:Switch命令大全(一)1.在基于IOS的交换机上设置主机名/系统名:switch(config)# hostname hostname在基于CLI的交换机上设置主机名/系统名:switch(enable) set system name name-string2.在基于IOS的交换机上设置登录口令:switch(config)# enable password level 1 password在基于CLI的交换机上设置登录口令:switch(enable) set passwordswitch(enable) set enalbepass3.在基于IOS的交换机上设置远
2、程访问:switch(config)# interface vlan 1switch(config-if)# ip address ip-address netmaskswitch(config-if)# ip default-gateway ip-address在基于CLI的交换机上设置远程访问:switch(enable) set interface sc0 ip-address netmask broadcast-addressswitch(enable) set interface sc0 vlanswitch(enable) set ip route default gateway4
3、.在基于IOS的交换机上启用和浏览CDP信息:switch(config-if)# cdp enableswitch(config-if)# no cdp enable为了查看Cisco邻接设备的CDP通告信息:switch# show cdp interface type modle/portswitch# show cdp neighbors type module/port detail在基于CLI的交换机上启用和浏览CDP信息:switch(enable) set cdp enable|disable module/port为了查看Cisco邻接设备的CDP通告信息:switch(en
4、able) show cdp neighborsmodule/port vlan|duplex|capabilities|detail5.基于IOS的交换机的端口描述:switch(config-if)# description description-string基于CLI的交换机的端口描述:switch(enable)set port name module/number description-string6.在基于IOS的交换机上设置端口速度:switch(config-if)# speed10|100|auto在基于CLI的交换机上设置端口速度:switch(enable) set
5、port speed moudle/number 10|100|autoswitch(enable) set port speed moudle/number 4|16|auto7.在基于IOS的交换机上设置以太网的链路模式:switch(config-if)# duplex auto|full|half在基于CLI的交换机上设置以太网的链路模式:switch(enable) set port duplex module/number full|half8.在基于IOS的交换机上配置静态VLAN:switch# vlan databaseswitch(vlan)# vlan vlan-num
6、name vlaswitch(vlan)# exitswitch# configure teriminalswitch(config)# interface interface module/numberswitch(config-if)# switchport mode accessswitch(config-if)# switchport access vlan vlan-numswitch(config-if)# end在基于CLI的交换机上配置静态VLAN:switch(enable) set vlan vlan-num name nameswitch(enable) set vlan
7、 vlan-num mod-num/port-list9. 在基于IOS的交换机上配置VLAN中继线:switch(config)# interface interface mod/portswitch(config-if)# switchport mode trunkswitch(config-if)# switchport trunk encapsulation isl|dotlqswitch(config-if)# switchport trunk allowed vlan remove vlan-listswitch(config-if)# switchport trunk allow
8、ed vlan add vlan-list在基于CLI的交换机上配置VLAN中继线:switch(enable) set trunk module/port on|off|desirable|auto|nonegotiateVlan-range isl|dotlq|dotl0|lane|negotiate10.在基于IOS的交换机上配置VTP管理域:switch# vlan databaseswitch(vlan)# vtp domain domain-name在基于CLI的交换机上配置VTP管理域:switch(enable) set vtp domain domain-name11.在基于
9、IOS的交换机上配置VTP 模式:switch# vlan databaseswitch(vlan)# vtp domain domain-nameswitch(vlan)# vtp sever|cilent|transparentswitch(vlan)# vtp password password在基于CLI的交换机上配置VTP 模式:switch(enable) set vtp domain domain-name mode sever|cilent|transparent password password12. 在基于IOS的交换机上配置VTP版本:switch# vlan data
10、baseswitch(vlan)# vtp v2-mode在基于CLI的交换机上配置VTP版本:switch(enable) set vtp v2 enable13. 在基于IOS的交换机上启动VTP剪裁:switch# vlan databaseswitch(vlan)# vtp pruning在基于CL I 的交换机上启动VTP剪裁:switch(enable) set vtp pruning enable14.在基于IOS的交换机上配置以太信道:switch(config-if)# port group group-number distribution source|destinati
11、on在基于CLI的交换机上配置以太信道:switch(enable) set port channel moudle/port-range modeon|off|desirable|auto15.在基于IOS的交换机上调整根路径成本:switch(config-if)# spanning-tree vlan vlan-list cost cost在基于CLI的交换机上调整根路径成本:switch(enable) set spantree portcost moudle/port costswitch(enable) set spantree portvlancost moudle/port c
12、ost costvlan-list16.在基于IOS的交换机上调整端口ID:switch(config-if)# spanning-treevlan vlan-listport-priority port-priority在基于CLI的交换机上调整端口ID:switch(enable) set spantree portpri mldule/portpriorityswitch(enable) set spantree portvlanpri module/portpriority vlans17. 在基于IOS的交换机上修改STP时钟:switch(config)# spanning-tre
13、e vlan vlan-list hello-time secondsswitch(config)# spanning-tree vlan vlan-list forward-time secondsswitch(config)# spanning-tree vlan vlan-list max-age seconds在基于CLI的交换机上修改STP时钟:switch(enable) set spantree hello intervalvlanswitch(enable) set spantree fwddelay delay vlanswitch(enable) set spantree
14、maxage agingtiamevlan18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:switch(config-if)#spanning-tree portfast在基于CLI的交换机端口上启用或禁用Port Fast 特征:switch(enable) set spantree portfast module/portenable|disable19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:switch(config)# spanning-tree uplinkfast max-update-rate pkts-per-second在基于
15、CLI的交换机端口上启用或禁用UplinkFast 特征:switch(enable) set spantree uplinkfast enable|disablerate update-rate all-protocols off|on20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name cvCisco认证知识:Switch命令大全(二)21. 为了从一条中继链路上删除VLAN,可使用下列命令:switch(enable) clear trunk modul
16、e/port vlan-range22. 用show vtp domain 显示管理域的VTP参数.23. 用show vtp statistics显示管理域的VTP参数.24. 在Catalyst交换机上定义TrBRF的命令如下:switch(enable) set vlan vlan-name name name type trbrf bridge bridge-numstp ieee|ibm25. 在Catalyst交换机上定义TrCRF的命令如下:switch (enable) set vlan vlan-num name name type trcrfring hex-ring-nu
17、m|decring decimal-ring-num parent vlan-num26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:switch(enable) set vlan vlan-num mod-num/port-num27. 命令show spantree显示一个交换机端口的STP状态.28. 配置一个ELAN的LES和BUS,可以使用下列命令:ATM (config)# interface atm number.subint multiointATM(config-subif)# lane serber-bu
18、s ethernet elan-name29. 配置LECS:ATM(config)# lane database database-nameATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-addressATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-addressATM(lane-config-databade)# name 30. 创建完数据库后,必须在主接口上启动LECS.命令如下:ATM(conf
19、ig)# interface atm numberATM(config-if)# lane config database database-nameATM(config-if)# lane config auto-config-atm-address31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:ATM(config)# interface atm number.subint multipointATM(config)# lane client ethernet vlan-num elan-num32. 用show lane server 显示LES的状态.33. 用show
20、lane bus显示bus的状态.34. 用show lane database显示LECS数据库可内容.35. 用show lane client显示LEC的状态.36. 用show module显示已安装的模块列表.37. 用物理接口建立与VLAN的连接:router# configure terminalrouter(config)# interface media module/portrouter(config-if)# description description-stringrouter(config-if)# ip address ip-addr subnet-maskrou
21、ter(config-if)# no shutdown38. 用中继链路来建立与VLAN的连接:router(config)# interface module/port.subinterfacerouter(config-ig)# encapsulationisl|dotlq vlan-numberrouter(config-if)# ip address ip-address subnet-mask39. 用LANE 来建立与VLAN的连接:router(config)# interface atm module/portrouter(config-if)# no ip addressro
22、uter(config-if)# atm pvc 1 0 5 qsaalrouter(config-if)# atm pvc 2 0 16 ilnirouter(config-if)# interface atm module/port.subinterface multipointrouter(config-if)# ip address ip-address subnet-maskrouter(config-if)# lane client ethernet elan-numrouter(config-if)# interface atm module/port.subinterface
23、multipointrouter(config-if)# ip address ip-address subnet-namerouter(config-if)# lane client ethernet elan-namerouter(config-if)# 40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:router(config)# ip routingrouter(config)# router ip-routing-protocolrouter(config-router)# network ip-network-numberrouter(config-rout
24、er)# network ip-network-numberCisco认证知识:Switch命令大全(三)41. 配置默认路由:switch(enable) set ip route default gateway42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:router(config)# interface interface numberrouter(config-if)# mls rp vlan-id vlan-id-num43. 在路由处理器启用MLSP:router(config)# mls rp ip44. 为了把一个外置的路由处理器接口和交换机安置在同一个
25、VTP域中:router(config)# interface interface numberrouter(config-if)# mls rp vtp-domain domain-name45. 查看指定的VTP域的信息:router# show mls rp vtp-domain vtp domain name46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:router(config-if)#mls rp management-interface47. 要检验MLS-RP的配置情况:router# show mls rp48. 检验特定接口上的MLS配置:rout
26、er# show mls rp interface interface number49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:set mls flow destination|destination-source|full50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:router(config)# mls rp ip input-acl51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:switch(enable) set mls enable52. 若想改变老化时间的值,可在特权模式下输入以下命令:s
27、witch(enable) set mls agingtime agingtime53. 设置快速老化:switch(enable) set mls agingtime fast fastagingtime pkt_threshold54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:switch(enable) show mls include55. 显示MLS高速缓存记录:switch(enable) show mls entry56. 用命令show in arp显示ARP高速缓存区的内容。57. 要把路由器配置为HSRP备份组的成员,可以在接口
28、配置模式下使用下面的命令:router(config-if)# standby group-number ip ip-address58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:router(config-if)# standy group-number preempt59. 访问时间和保持时间参数是可配置的:router(config-if)# standy group-number timers hellotime holdtime60. 配置HSRP跟踪:router(config-if)# standy group-number track type-number
29、 interface-priority61. 要显示HSRP路由器的状态:router# show standby type-number group brief62. 用命令show ip igmp确定当选的查询器。63. 启动IP组播路由选择:router(config)# ip muticast-routing64. 启动接口上的PIM:dalllasr1(config-if)# ip pim dense-mode|sparse-mode|sparse-dense-mode65. 启动稀疏-稠密模式下的PIM:router# ip multicast-routingrouter# int
30、erface type numberrouter# ip pim sparse-dense-mode66. 核实PIM的配置:dallasr1# show ip pim interfacetype number count67. 显示PIM邻居:dallasr1# show ip neighbor type number68. 为了配置RP的地址,命令如下:dallasr1# ip pim rp-address ip-address group-access-list-numberoverride69. 选择一个默认的RP:dallasr1# ip pim rp-address通告RP和它所服
31、务的组范围:dallasr1# ip pim send-rp-announce type number scope ttl group-list access-list-number为管理范围组通告RP的地址:dallasr1# ip pim send-rp-announce ethernet0 scope 16 group-list1dallasr1# access-list 1 permit 266.0.0.0 0.255.255.255设定一个RP映像代理:dallasr1# ip pim send-rp-discovery scope ttl核实组到RP的映像:dallasr1# show ip pim rp mappingdallasr1# show ip pim rp group-name|group-address mapping70. 在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL阀值:dallasr1(config-if)# ip multicast ttl-threshold ttl-value
链接地址:https://www.31doc.com/p-2726714.html