焊接技术培训-AWSD1.ppt
《焊接技术培训-AWSD1.ppt》由会员分享,可在线阅读,更多相关《焊接技术培训-AWSD1.ppt(74页珍藏版)》请在三一文库上搜索。
1、AWS D1.1 &EEMUA 158 不同要求,焊接技术培训,之,质量部 焊接室,AWS D1.1 &EEMUA 158 不同要求,内 容,A 课程培训概述(Preface) B 内 容 (Content) 1. 标准的范围(Scope ) 2. 材料(Material ) 3. 焊接工艺和焊工的评定(Qualification of WPS and welder) 4. 建造(Construction and Fabrication) 5. 外观检测(Visual inspection),焊接技术培训,A.课程培训概述,通过本次培训,让各位了解AWS D1.1 2010和 EEMUA 15
2、8: 1994 标准的基本内容,了解两标准中一些重点要求及其不同。了解建造过程中的相关要求,以免违反标准和工艺文件要求。减少船东、船检的Comments、投诉等,提高产品质量,加快报验过程,在建造和检验过程中,减少因不了解EEMUA 158标准中的要求而出现不必要的问题和麻烦。,焊接技术培训,1. 标准的范围(Scope ),AWS D1.1 &EEMUA 158 不同要求,AWS D1.1 This code contains the requirements for fabricating and erecting welded steel structures. When this co
3、de is stipulated in contract documents, conformance with all provisions of the code shall be required, except for those provisions that the Engineer (see 1.4.1) or contract documents specifically modifies or exempts. 钢结构建造的基本要求。 EEMUA158:1994 This Specification defines the basic requirements for the
4、 fabrication work on primary structures of offshore installations. These will normally include, but not be limited to, the following: jacket structure including nodes, cones, braces, legs and conductor framing piles and followers J-tubes and caissons riser clamps flotation tanks and buoyancy tubes m
5、odule support frame including nodes, cones, braces, padears, module framing including nodes, columns, fabricated beams and padears. Flareboom helideck - when constructed of steel any other areas designated primary on the Drawings. 海洋工程重要结构建造的基本要求。结构(TKY节点、管子节点、拉筋支撑、桩腿、导管架、浮箱、浮筒、框架模块、吊耳、直升机平台等重要结构)。,
6、2. Material 材料,AWS D1.1 &EEMUA 158 不同要求,AWS D1.1 -2010/2008 Clause 3 Prequalification of WPSs 按材料等级和强度进行了分类。 AWS D1.1 的 5.2 和 5.3 条款比EEMUA 158 1994 section 3 更详细的讲述了,焊材、钢板等材料的替代、储存、标识、发放等 。 这些都要严格按程序的要求控制好。 EEMUA 158:1994 中规定,生产中所用的母材的供货状态必须与材料评定试验中所用的母材有相同的供货状态。 (N389项目用板供货状态TMCP),3. Qualification
7、of WPS and welder 焊接工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,AWS D1.1 -2010/2008 Section 4 Qulification Part B 对焊评做了详细的规定和要求。 Part C 对焊工资质考试做了相关的规定和要求。 而 EEMUA 158: 1994 section 4 Qualification of welding procedures and personnel 在焊接工艺评定中对一些重要变素和限制条件进行了比AWS D1.1 更为严格的要求。 当然AWS D1.1 也有比EEMUA 158 要求严格的条款。 下面先
8、来了解对其中一些不同要求。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.3 Restrictions on Welding Practices 焊接过程中的限制(选10条) (a) SMAW for heat inputs exceeding 3 kJ/mm. 手工电弧焊热输入不允许超3 kJ/mm。 (b) SMAW bead widths exceeding the lesser of 16 mm or four times the core
9、wire diameter. 焊条电弧焊根部打底焊道宽度不能超4倍焊条直径或16mm. 我们WPS要求2.5倍。很多海工产品的规格书也是这样规定的,尤其对重要结构、特殊结构。 AWS D1.1 对SMAW的焊道宽度没有作出要求。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.3 Restrictions on Welding Practices 焊接过程中的限制 (h) SSFCAW and GSFCAW for heat inputs exceed
10、ing 1.5 kJ/mm except for vertical-up root passes. 药芯气体保护焊(气体保护和自保护)热输入除根部立焊焊道外,不得超1.5 kJ/mm。 所以立焊时,要控制焊道宽度不得超宽(WPS要求小于12mm)。还要按WPS控制好焊接参数。 AWS D1.1 根据坡口宽度,要求分道。非管材1G,2G,4G位置,坡口间距16mm时,分道焊接。非管材3G,或管材几个位置焊接,25mm, 分道焊接。 (l) Heat inputs exceeding 3.5 kJ/mm for steels up to and including Grade 355 and ex
11、ceeding 3 kJ/mm for grades above 355. 埋弧焊(SAW),焊接屈服强度355Mpa以下钢材时热输入3.5 kJ/mm, 超过355Mpa时,热输入3 kJ/mm。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.3 Restrictions on Welding Practices 焊接过程中的限制 (o) Included angles of bevelled welds below 45 degrees (exc
12、ept as covered by 4.5.2 (g). 焊缝的坡口角度不得小于45(除已经成功评定覆盖小角度外) (p) Included angles below 60 degrees for closing welds in tubulars above 40 mm thick. 40mm以上板厚的管道上,封闭焊接接头的坡口角度不得小于 60。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.3 Restrictions on Welding P
13、ractices 焊接过程中的限制 (S) Maximum interpass temperature exceeding 250C. 最高层间温度250。 现场按适用的WPS要求来控制温度。 AWS D1.1 对材料的最高预热和层间温度不得高于PQR中最高层间温度56以上。 AWS D1.1 表4.5规定了最低预热温度和层间温度最多可以降低15。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.3 Restrictions on Welding Pr
14、actices 焊接过程中的限制 (T) Single-pass fillet welds (other than by SAW) with a design leg length greater than 6 mm. 单道角焊缝(除了SAW)焊脚大于6mm,重评。,AWS D1.1 中,表5.8,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.3 Restrictions on Welding Practices 焊接过程中的限制 (V) Use o
15、f backing strips. 背部使用带(钢)状衬垫,重评。 (U) Use of ceramic inserts. 使用陶瓷衬垫,重评。 AWS D1.1 中,表4.5 中第34条:取消衬垫或取消背部清根,要重评。 5.10 衬垫 有坡口焊缝或角焊缝的根部可用铜、焊剂、玻璃纤维带、陶瓷、铁粉或类似材料作衬垫以防熔穿。 N389项目提交的焊评没有使用衬垫评定的。所以现场严禁使用衬垫。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.5 Essen
16、tial Variables (基本变素) 现场生产中,若与4.5.1到4.5.5 中规定的不同,要重新做评定试验。 以下是选的一些规定,建造过程中需要注意,并严格按批准的适用的WPS执行。 4.5.1 Materials Related Variables (材料相关的变素) (f ) If flame-cut weld bevels are not ground to bright metal. 火焰切割后的焊缝坡口面打磨至光亮的金属。(否则重评) (g) If a protective finish applied to the weld bevel is changed. 如果坡口采用
17、的底漆,底漆不可更换。(否则重评) 我们做焊评的试件坡口都是打磨干净的。没有做过 涂坡口漆的焊评。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.5 Essential Variables 4.5.2 Weld Geometry Related Variables (坡口尺寸相关的变素) (f) If the shape of the weld preparation changes, except that: a single bevel qual
18、ifies a single V; K qualifies X; and 2:1 and 1:1 preparations qualify each other and all intermediate geometries. 坡口覆盖。按WPS选用。 1/2 V只能支持1/2V或V型坡口;K型只能支持K和X型坡口。,AWS D1.1 Section 3 table 4. 坡口覆盖。图3.4 改变坡口类型 (例如:单面 V 形坡口 改为双 V 形坡口,重评)。 坡口形式按提交的WPS选用。 顺便提下,EEMUA 158 规定对接焊板或T型接头腹板超过8mm时,都要开坡口。,3. Qualifi
19、cation of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.5 Essential Variables 4.5.2 Weld Geometry Related Variables (坡口尺寸坡口尺寸相关的变素) (g) If the included angle of the groove is less than the value tested and qualified by the WPS. Acute angles in stub to barrel welds, wher
20、e the included angle is less than 45, are qualified by the test in 4.4.2.3(b). 坡口的角度不小于WPS中的规定。否则重评。 在TKY接头中,支管和主管的夹角小于45,要通过试验评定。 (N389项目已经评定过了),AWS D1.1 TKY接头坡口角度()小于 30时,不免除评定。要通过试验评定。,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.5.2 Weld Geometr
21、y Related Variables (坡口尺寸相关的变素) (h) For single-sided welds: if the root face is more than 0.5 mm above or 1.5 mm below that qualified, or if the root gap is more than 3.0 mm above or 0.5 mm below that qualified. 单边坡口: 根部钝边公差 f (+0.5, -1.5); 根部间隙公差 R (+3 , -1.5); (i) For double-sided welds: if the ro
22、ot face is more than 2 mm above or below that qualified or if the root gap exceeds 6 mm. 双边坡口: 根部钝边公差 f (+2, -2); 根部间隙公差 R ( 6);,AWS D1.1 中不按单边坡口、双面坡口分,而是按以下三种情况:,背部碳刨 f (+2, -2); R (+2 , -3); (+10,-5),3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEMUA 158 不同要求,EEMUA 158: 1994 Section 4 4.5
23、Essential Variables 4.5.2 Weld Geometry Related Variables (坡口尺寸相关的变素) (j) For fillet welds, any increase in root gap. 角焊缝,不得增加根部间隙。 However, for multipass fillet welds any root gap shall be compensated for by a corresponding increase in fillet leg length up to a maximum of 6 mm. 除非多道角焊缝要深熔,间隙增加,焊脚应加
24、大相应增加。增量最大不超过6mm. For single-pass fillet welds the root gap shall be limited to 3 mm maximum, and the weld leg length shall be increased by the same amount. 单道角焊缝根部间隙最大不超过3mm. AWS D1.1 5.22 规定 角焊缝和PJP坡口焊缝间隙5mm。 间隙尽量小。除特殊情况外,当板厚大于75mm,加衬垫允许8mm.,3. Qualification of WPS and welder 工艺和焊工评定,AWS D1.1 &EEM
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 焊接 技术培训 AWSD1
链接地址:https://www.31doc.com/p-2913737.html