BIOWIN_Tutorial.pdf
《BIOWIN_Tutorial.pdf》由会员分享,可在线阅读,更多相关《BIOWIN_Tutorial.pdf(21页珍藏版)》请在三一文库上搜索。
1、BioWIN Tutorial Damian KrukDamian Kruk, MSc Email: umkrukdcc.umanitoba.ca Office hours: Thu,13:30-14:30; E1-246 Goal :Goal : Setup steady state model that simulates designed plant 2 BioWin Tutorial, D. Kruk BIOWIN WWTP simulator AS/AD model Nitrogen removal (conventional and autotrophic) Phosphorus
2、removal Anaerobic digestion To predict effluent quality under given conditions To prevent over-design or under-design Maintenance scheduling Check retrofitting scenarios during WWTP upgrading 3 BioWin Tutorial, D. Kruk Just an introduction to modeling. Start after your hand calculation is finished.
3、In this case model is for verification of your design. Input data you need: Influent characteristics (after screen and grit chamber) Volume and depth of all tanks Flow splits for all junctions You will design only 1 train regardless of your actual plan. 4 BioWin Tutorial, D. Kruk Q 0.25Q 0.25Q 0.25Q
4、 0.25Q 0.25Q 0.25Q 5 BioWin Tutorial, D. Kruk To create item (tank, pipe, splitter etc) drag and drop it from “Configure” tab To change properties of items right-click on them Name Dimensions Local temperature (e.g. in digester) All items have to be connected To change global parameters (e.g. temper
5、ature) go to “project” menu and choose your option No copy and paste option To see results after changes were applied new simulation has to be run 6 BioWin Tutorial, D. Kruk “COD influent” or “BOD influent” What you need Flow rate, Total COD (or cBOD5), Total TKN, Total P, Inorganic SS Average dry w
6、eather condition To create : Configure Tab COD influent To edit : Right click and go to Properties Data input (check the units!) Use the default value for these Nitrate N (0 mg/L), pH (7.3) Alkalinity (6 mmol/L), Calcium (80 mg/L) Magnesium (15 mg/L), DO (0 mg/L) BioWin Tutorial, D. Kruk 7 8 BioWin
7、Tutorial, D. Kruk Screen and grit chamber Dont need to have in BIOWIN design Actual design needs them Primary settling (not required for this project) You should have the dimensions of PS before modeling. To create: Configure Primary tank (ideal) Parameters to setup Dimensions : volume, depth, width
8、 Flow split : underflow based on your calculation Operation : input SS removal efficiency based on your design (50% - 70%, depending on your tank type) BioWin Tutorial, D. Kruk 9 10 BioWin Tutorial, D. Kruk You have to decide what process you will use. Westside will be shown here. Preanoxic anaerobi
9、c anoxic aerobic How to create: Configure - bioreactor Double click on the icon to setup properties. DO and dimensions To simulate plug flow divide big tanks to group of smaller ones E.g. 18 000 m3 aerobic zone will be modeled as 3 connected in serial aerated tanks with vol. of 6 000m3/each BioWin T
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BIOWIN_Tutorial
链接地址:https://www.31doc.com/p-3579611.html