【AS澳大利亚标准】AS NZS 60745.2.1-2009 Hand-held motor-operated electric tools—Safety Part 2.1 Particular requirements for drills and impact drills.doc
《【AS澳大利亚标准】AS NZS 60745.2.1-2009 Hand-held motor-operated electric tools—Safety Part 2.1 Particular requirements for drills and impact drills.doc》由会员分享,可在线阅读,更多相关《【AS澳大利亚标准】AS NZS 60745.2.1-2009 Hand-held motor-operated electric tools—Safety Part 2.1 Particular requirements for drills and impact drills.doc(25页珍藏版)》请在三一文库上搜索。
1、AS/NZS 60745.2.1:2009AS/NZS 60745.2.1:2009IEC 60745-2-1 Ed 2.1, IDTAustralian/New Zealand StandardHand-held motor-operated electric toolsSafetyPart 2.1: Particular requirements for drills and impact drillsThe Standard is downloaded from Standard SharingAS/NZS 60745.2.1:2009This Joint Australian/New
2、 Zealand Standard was prepared by Joint Technical Committee EL-002, Safety of Household and Similar Electrical Appliances and Small Power Transformers. It was approved on behalf of the Council of Standards Australia on 17 March 2009 and on behalf of the Council of Standards New Zealand on 13 March 2
3、009.This Standard was published on 29 May 2009.The following are represented on Committee EL-002:Australian Industry GroupAustralian Retailers AssociationBusiness New ZealandConsumer Electronic Suppliers Association, AustraliaConsumers Federation of AustraliaElectrical regulatory authorities, Austra
4、lia Electrical Compliance Testing Association Electrical consultantsEngineers AustraliaAssociation of Certification BodiesMinistry of Consumer Affairs, New ZealandNew Zealand Electric Fence Energizer Manufacturers Standards GroupKeeping Standards up-to-dateStandards are living documents which reflec
5、t progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Sta
6、ndard, which should include any amendments which may have been published since the Standard was purchased.Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Web Shop at .au or Standards New Zealand web site at www.standards.co.nz and looking up t
7、he relevant Standard in the on-line catalogue.Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. For more frequent listings or notification of revisions, amendments and withdrawals, Standards Australia and Standards New Zealand offer a n
8、umber of update options. For information about these services, users should contact their respective national Standards organization.We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Pl
9、ease address your comments to the Chief Executive of either Standards Australia or Standards New Zealand at the address shown on the back cover.This Standard was issued in draft form for comment as DR 08985.AS/NZS 60745.2.1:2009Australian/New Zealand StandardHand-held motor-operated electric toolsSa
10、fetyPart 2.1: Particular requirements for drills and impact drillsOriginated in Australia as AS C1601959. Previous edition AS/NZS 3160:1996.Jointly revised and redesignated, in part, as AS/NZS 60745.2.1:2003. Jointly revised and redesignated as AS/NZS 60745.2.1:2009.COPYRIGHT Standards Australia/Sta
11、ndards New ZealandAll rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.Jointly published by Standards Australia, GPO Box 476, Sydney, NSW 2001 and Stand
12、ardsNew Zealand, Private Bag 2439, Wellington 6020ISBN 0 7337 9102 63The Standard is downloaded from Standard SharingCONTENTSFOREWORD.41Scope .62Normative references .63Terms and definitions .64General requirements .65General conditions for the tests .66Void .77Classification .78Marking and instruc
13、tions .79Protection against access to live parts .710 Starting .711 Input and current .712 Heating .713 Leakage current .814 Moisture resistance .815 Electric strength .816 Overload protection of transformers and associated circuits .817 Endurance .818 Abnormal operation .919 Mechanical hazards .920
14、 Mechanical strength .921 Construction . 1022 Internal wiring. 1023 Components . 1024 Supply connection and external flexible cords . 1025 Terminals for external conductors . 1026 Provision for earthing. 1027 Screws and connections . 1028 Creepage distances, clearances and distances through insulati
15、on . 1129 Resistance to heat, fire and tracking . 1130 Resistance to rusting . 1131 Radiation, toxicity and similar hazards . 11Annexes . 16Annex K (normative) Battery tools and battery packs . 16Annex L (normative) Battery tools and battery packs provided with mains connectionor non-isolated source
16、s . 17Annex ZZ (informative) Variations to IEC 60745-2-1 Ed 2.1 for application in Australiaand New Zealand . 19Bibliography . 18Figure 101 Testing apparatus . 13Figure 102 Reaction torque of single-hand support . 14Figure 103 Reaction torque of double-hand support . 155The Standard is downloaded fr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AS澳大利亚标准 【AS澳大利亚标准】AS NZS 60745.2.1-2009 Hand-held motor-operated electric toolsSafety Part 2.1 Particular AS
链接地址:https://www.31doc.com/p-3619501.html