【BS英国标准】BS EN 869-2006 Safety of machinery. Safety requirements for pressure metal diecasting units.doc
《【BS英国标准】BS EN 869-2006 Safety of machinery. Safety requirements for pressure metal diecasting units.doc》由会员分享,可在线阅读,更多相关《【BS英国标准】BS EN 869-2006 Safety of machinery. Safety requirements for pressure metal diecasting units.doc(47页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARDBS EN 869:2006Safety of machinery Safety requirements for pressure metal diecasting unitsThe European Standard EN 869:2006 has the status of a BritishStandardICS 25.120.30 BS EN 869:2006National forewordThis British Standard was published by BSI. It is the UK implementation ofEN 869:
2、2006. It supersedes BS EN 869:1998 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee MCE/3, Safeguarding of machinery, to Subcommittee MCE/3/10, Foundry machinery Safety.A list of organizations represented on MCE/3/10 can be obtained on request to its se
3、cretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amd. No.DateCommentsThis British Standard was published under the author
4、ity of the Standards Policy and Strategy Committeeon 31 October 2006 BSI 2006ISBN 0 580 49036 XAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 869September 2006ICS 25.120.30Supersedes EN 869:1997English VersionSafety of machinery - Safety requirements for pressu
5、re metal diecasting unitsScurit des machines - Prescriptions de scurit pour les chantiers de moulage des mtaux sous pressionSicherheit von Maschinen - Sicherheitsanforderungen anMetall-DruckgieanlagenThis European Standard was approved by CEN on 6 August 2006.CEN members are bound to comply with the
6、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or
7、 to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versio
8、ns.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
9、 Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide fo
10、r CEN national Members.Ref. No. EN 869:2006: EEN 869:2006 (E)ContentsPageForeword.5Introduction .61Scope .62Normative references .63Terms and definitions .84List of significant hazards .114.1General.114.2Mechanical hazards .114.3Electrical hazards/control system.124.4Thermal hazards .124.5Fire hazar
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS英国标准 【BS英国标准】BS EN 869-2006 Safety of machinery. requirements for pressure metal diecasting units BS
链接地址:https://www.31doc.com/p-3620412.html