(BS英国标准)BS EN 50144-2-16-2003 手持电动工具的安全.用平头钉钉东西的工具的特殊要求.doc
《(BS英国标准)BS EN 50144-2-16-2003 手持电动工具的安全.用平头钉钉东西的工具的特殊要求.doc》由会员分享,可在线阅读,更多相关《(BS英国标准)BS EN 50144-2-16-2003 手持电动工具的安全.用平头钉钉东西的工具的特殊要求.doc(17页珍藏版)》请在三一文库上搜索。
1、EUROPEAN STANDARD EN 50144-2-16NORME EUROPENNEEUROPISCHE NORM July 2003ICS 25.140.99English versionSafety of hand-held electric motor operated toolsPart 2-16: Particular requirements for tackersScurit des outils lectroportatifs moteurPartie 2 -16: Rgles particulires pour les agrafeusesSicherheit han
2、dgefhrter motorbetriebenerElektrowerkzeugeTeil 2-16: Besondere Anforderungen fr EintreibgerteThis European Standard was approved by CENELEC on 2003 -02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard t
3、he status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, Ger
4、man). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Re
5、public, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.CENELECEuropean Committee for Electrotechnical StandardizationComit Euro pen de Normalisation Elec
6、trotechniqueEuropisches Komitee fr Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B - 1050 Brussels 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 50144-2-16:2003 E- 17 -EN 50144 -2-16:2003ForewordThis Euro
7、pean Standard has been prepared by the Technical Committee CENELEC TC 61F, Safety of hand -held and transportable motor -operated electric tool s. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50144-2-16 on 2003 -02 -01.The following dates w
8、ere fixed:- latest date by which the EN has to be implemented at national level by publication o f an identicalnational standard or by endorsement (dop) 2004 -02 -01- latest date by which the national standards conflictingwith the EN have to be withdrawn (dow) 2006 -02 -01This standard is divided in
9、to two partsPart 1 General requirements whi ch are common to most hand -held electric motor -operated tools(for the purpose of this standard referred to simply as tools)Part 2 Requirements for particular types of tools which either supplement or modify the requirements given in Part 1 to account fo
10、r the particular hazards and characteristics of these sp ecific tools.This European Standard has been prepared under a mandate given to CEN/CENELEC by the European Commission and the European Free Trade Association and supports the essential health and saf ety requirements of the Machinery Directive
11、.Compliance with the relevant clauses of Part 1 together with this Part 2 provides one means of conforming with the specified essential health and safety requirements of the Directive.For noise and vibration, th is standard covers the requirements for their measurement, the provision of information
12、arising from t hese measurements and the provisions of information about the personal protective equipment required.Specific requirements for the reduction of the risk arising from noise and vibration through the design of the tool are not given as this reflects the current state of the art.CEN/TC 2
13、55 has produced standards for non electric tackers (EN 792 -13).Warning: Other requirements arising from other EC Directiv es can be applicable to the products falling within the scope of this standard.This standard follows the overall requirements of EN 292 -1 and EN 292 -2.Subclauses, tables and f
14、igures which are additional to those in Part 1 are numbered starting from 101.NOTE In this standard the following print types are used:- requirements proper;- test specifications;- explanatory matter.Contentspage1 Scope. . . . 42 Definitions . . . . 43 General requirements . . . 44 General condition
15、s for the tests . . . 45 Rating . . . . 46 Classification . . . . 47 Marking and information for use . . . 58 Protection against electric shock . . . 59 Starting . . . . 510 Input and current . . . . 511 Heating . . . . 512 Leakage current . . . . 513 Environmental requirements . . . 614 Moisture re
16、sistance . . . 1015 Insulation resistance and electric strength . . . 1016 Endurance . . . . 1117 Abnormal operation . . . 1118 Mechanical hazards . . . 1119 Mechanical strength . . . 1120 Construction . . . . 1221 Components . . . . 1222 Internal wiring . . . . 1223 Supply connection and external f
17、lexible cables and cords . . 1224 Terminals for external conductors. . . . 1225 Provision for earthing . . . 1226 Screws and connections . . . 1227 Creepage distances, clearances and distances through insulation . 1228 Resistance to heat, fire and tracking . . . 1229 Resistance to rusting . . . 1230
18、 Radiation . . . . 12Annexes . . . . 13Fi gure 101 - Location of the measurement positions for tackers . . 14Figure 102 - Working position of operator . . . 15Figure 103 - Test rig . . . . 15Figure 104 - Glueing of transducer . . . 16Figure 105 - Measurement direction and position of transducer . .
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS英国标准BS EN 50144-2-16-2003 手持电动工具的安全.用平头钉钉东西的工具的特殊要求 BS 英国 标准 50144 16 2003 手持 电动工具 安全 平头 东西 工具 特殊要求
链接地址:https://www.31doc.com/p-3628155.html