BS EN 3373-010-2009 航空航天系列.电导体压接用终端盒和内嵌式接头.米制和英制螺栓系列用温度低于150℃铜导体压接用镀锡环型终.pdf

《BS EN 3373-010-2009 航空航天系列.电导体压接用终端盒和内嵌式接头.米制和英制螺栓系列用温度低于150℃铜导体压接用镀锡环型终.pdf》由会员分享，可在线阅读，更多相关《BS EN 3373-010-2009 航空航天系列.电导体压接用终端盒和内嵌式接头.米制和英制螺栓系列用温度低于150℃铜导体压接用镀锡环型终.pdf（12页珍藏版）》请在三一文库上搜索。

1、 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3373-010 February 2009 ICS 49.060 English Version Aerospace series - Terminal lugs and in-line splices for crimping on electric conductors - Part 010: Terminal lugs, ring shaped, tin plated, for crimping on copper conductors, temperature up to 15

2、0 C for metric and inch stud series - Product standard Srie arospatiale - Cosses et prolongateurs pour sertissage sur conducteurss lectriques - Partie 010: Cosses, rondes, tames pour sertissage sur conducteurs en cuivre, temprature jusqu 150 C pour bornages filets en mriques et en pouces - Norme de

3、produit Luft- und Raumfahrt - Kabelschuhe und Verlngerungen fr das Crimpen auf elektrische Leiter - Teil 010: Kabelschuhe, ringfrmig, (verzinnt) fr das Crimpen auf Kupferleitungen, Betriebstemperatur bis 150 C fr metrische und zllige Gewindebolzen - Produktnorm This European Standard was approved by

4、 CEN on 11 July 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standard

5、s may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respons bility of a CEN member into its own language and notified to t

6、he CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Neth

7、erlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation

8、 in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3373-010:2009: E EN 3373-010:2009 (E) 2 Contents Page Foreword 3 1Scope 4 2Normative references 4 3Terms and definitions .4 4Characteristics .4 5Dimensions and mass .4 6Designation 8 7Quality assurance 8 8Details

9、of assembly tooling 9 8.1Crimping tools 9 8.2Die dimensions 9 9Marking .9 10Packaging .9 EN 3373-010:2009 (E) 3 Foreword This document (EN 3373-010:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried ou

10、t in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publ

11、ication of an identical text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the latest by August 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC s

12、hall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, E

13、stonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3373-010:2009 (E) 4 1 Scope This standard defines the characteri

14、stics of tin plated copper ring shaped terminals for crimping on copper conductors. They are for use on both metric and inch dimension studs at temperatures up to 150 C maximum. This standard should be used in conjunction with EN 3373-001. 2 Normative references The following referenced documents ar

15、e indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 2591-*, Aerospace series El

16、ements of electrical and optical connection Test methods EN 3373-001, Aerospace series Terminal lugs and in-line splices for crimping on electric conductors Part 001: Technical specification SAE-AS 20659, Terminal, lug crimp style, copper, uninsulated, ring tongue, type I, class I, for 175 C total c

17、onductor temperature1) MIL-DTL-22520, Crimping tools, wire termination, general specification for 2) MS25441, Crimping tool, terminal, hydraulic operated, wire size 8 thru 4/0 2) 3) MS90485, Dies, crimping tool, for use with MS20659 uninsulated wire terminals (for wire sizes 8 through 4/0) 2) 3 Term

18、s and definitions For the purposes of this document, the terms and definitions given in EN 3373-001 apply. 4 Characteristics The operational range for tin plated terminal lugs shall be 65 C to 150 C. When split barrel construction is used the split shall be permanently sealed and shall not open as a

19、 result of crimping. All surfaces shall be smooth and free from burrs and sharp edges. 5 Dimensions and mass For dimensions and mass, see Table 1 and Figure 1. These dimensions are based upon metric conversions of SAE-AS 20659. * All parts quoted in this standard. 1) Published by: Society of Automot

20、ive Engineering (SAE), 400 Commonwealth Drive, Warrendale, PA 15096, USA. 2) Published by: Department of Defense (DOD), the Pentagon, Washington D.C. 20301 USA. 3) Inactive for new design EN 3373-010:2009 (E) 5 Table 1 Crimp lug dimensions Dimensions in millimetres Code Wire size Stud size A max. B

21、min. C rad min. D E F G J W max. min. max. min. min. max. min. 001 004 - 010 (22-18) 2,18 (2) 22,61 6,35 2,92 1,14 0,58 3,56 1,85 2,49 2,29 3,05 6,60 4,52 002 2,84 (4) 3,17 3,10 2,90 003 3,50 (6) 3,86 3,61 5,84 004 4,83 (10) 24,59 4,37 5,16 4,90 8,13 7,75 005 7,92 (5/16) 30,15 7,21 2,92 1,32 8,58 8,

22、20 13,72 11,43 006 9,52 (3/8) 33,22 8,33 10,16 9,78 13,72 13,21 007 12,70 (1/2) 38,86 9,60 13,34 12,95 18,62 17,86 008 012 - 020 (16 - 14) 0,284 (4) 24,05 6,35 3,17 1,35 0,74 4,12 2,41 3,10 2,90 3,89 6,76 5,94 009 3,50 (6) 24,26 4,37 3,86 3,61 8,31 7,54 010 23,97 3,17 6,76 5,94 011 4,83 (10) 24,26 4

23、,37 5,15 4,90 8,31 7,54 012 7,92 (5/16) 31,72 7,21 3,68 2,06 8,58 8,20 13,72 11,53 013 9,52 (3/8) 32,77 8,33 10,16 9,78 13,61 014 12,70 (1/2) 40,46 9,60 13,33 12,95 18,62 17,86 015 030 - 050 (12 - 10) 3,50 (6) 24,26 6,35 5,13 2,03 0,96 5,84 3,53 4,52 3,61 N/A 8,05 7,37 016 4,83 (10) 24,4 4,37 5,16 4

24、,90 9,93 9,27 017 7,92 (5/16) 29,36 7,52 5,33 3,28 8,58 8,20 13,89 12,32 018 9,52 (3/8) 29,77 8,33 10,16 9,78 15,19 13,61 019 12,70 (1/2) 43,64 9,60 13,33 12,95 18,62 17,86 020 090 (8) 4,17 (8) 29,10 8,00 5,94 2,13 0,96 6,91 4,72 4,52 4,27 10,90 9,80 021 4,83 (10) 5,16 4,90 022 6,35 (1/4) 30,96 6,73

25、 6,99 6,60 12,14 11,05 023 7,92 (5/16) 32,94 7,52 6,60 4,47 8,58 8,20 14,97 13,89 024 9,52 (3/8) 8,33 10,16 9,78 025 12,70 (1/2) 39,24 11,18 13,33 12,95 21,16 17,27 continued EN 3373-010:2009 (E) 6 Table 1 Crimp lug dimensions (continued) Code Wire size Stud size A max. B min. C rad min. D E F G J W

26、 max. min. max. min. min. max. min. 026 140 (6) 4,83 (10) 33,32 9,52 6,05 2,13 1,09 8,03 5,89 5,16 4,90 N/A 12,78 11,68 027 6,35 (1/4) 6,73 6,98 6,60 028 7,92 (5/16) 36,50 7,75 8,58 8,20 15,82 14,73 029 9,52 (3/8) 8,33 7,49 5,64 10,16 9,78 030 12,70 (1/2) 42,57 11,18 13,33 12,95 21,16 17,78 031 220

27、(4) 4,83 (10) 35,56 11,10 7,01 2,44 1,19 9,65 7,37 5,16 4,90 15,95 12,19 032 6,35 (1/4) 6,98 6,60 033 7,92 (5/16) 48,01 7,8232 8,58 8,20 16,46 15,37 034 9,52 (3/8) 8,3312 9,27 7,11 10,16 9,78 035 12,70 (1/2) 43,71 11,176 13,33 12,95 21,16 18,03 036 340 (2) 4,83 (10) 43,99 12,83 8,71 2,77 1,37 12,01

28、9,27 5,16 4,90 18,06 16,97 037 6,35 (1/4) 6,98 6,60 038 7,92 (5/16) 8,58 8,20 039 9,52 (3/8) 11,43 9,017 10,16 9,78 040 11,1 (7/16) 48,13 11,51 11,76 11,38 20,42 18,80 041 12,70 (1/2) 13,33 12,9 042 420 (1) 6,35 (1/4) 46,86 14,35 9,73 3,17 1,78 13,39 10,11 6,98 6,60 19,89 18,80 043 7,92 (5/16) 8,58

29、8,20 044 9,52 (3/8) 10,16 9,779 045 11,1 (7/16) 50,29 11,51 12,83 9,85 11,76 11,38 22,51 18,80 046 12,70 (1/2) 13,33 12,95 047 530 (0) 6,35 (1/4) 51,94 16,00 10,62 3,17 1,78 14,68 11,63 6,98 6,60 21,67 20,57 048 7,92 (5/16) 8,58 8,20 049 9,52 (3/8) 10,16 9,779 050 11,1 (7/16) 53,14 11,51 14,17 11,12

30、 11,76 11,38 22,94 21,84 051 12,70 (1/2) 13,33 12,95 continued EN 3373-010:2009 (E) 7 Table 1 Crimp lug dimensions (concluded) Code Wire size Stud size A max. B min. C rad min. D E F G J W max. min. max. min. min. max. min. 052 680 (00) 6,35 (1/4) 58,93 17,78 12,01 3,28 1,90 16,26 13,21 6,98 6,60 N/

31、A 24,28 23,65 053 7,92 (5/16) 8,58 8,20 054 9,52 (3/8) 15,75 12,7 10,16 9,779 055 11,1 (7/16) 11,76 11,38 056 12,70 (1/2) 13,33 12,95 057 850 (000) 7,92 (5/16) 62,36 18,24 13,03 3,56 2,16 18,14 14,66 8,58 8,20 26,75 25,6 058 9,52 (3/8) 10,16 9,779 059 11,1 (7/16) 17,53 14,15 11,76 11,38 060 12,70 (1

32、/2) 13,33 12,95 061 107 (0000) 7,92 (5/16) 69,98 18,64 14,22 3,81 2,41 19,91 16,38 8,58 8,20 29,16 27,81 062 9,52 (3/8) 10,16 9,78 063 11,1 (7/16) 11,76 11,38 064 12,70 (1/2) 19,30 15,8 13,33 12,95 065 (5/8) 16,92 16,53 066 (3/4) 75,06 19,43 19,94 19,56 067 (7/8) 75,46 23,11 22,73 32,21 30,48 EN 337

33、3-010:2009 (E) 8 Terminals for conductor sizes 004 - 020 Terminals for conductor sizes 030 - 107 Key 1 Inspection hole required Figure 1 6 Designation EXAMPLE Description block TERMINAL LUG Identity block EN3373-010-XXX-001 Reference of this standard Item code (see Tables 1 and 2) 7 Quality assuranc

34、e Quality assurance shall be in accordance with EN 3373-001. EN 3373-010:2009 (E) 9 Table 2 Designation of the test Details EN 2591-101 Visual examination Applicable EN 2591-102 Examination of dimensions and mass Applicable EN 2591-206 Measurement of insulation resistance Not applicable EN 2591-217

35、Voltage drop under specified current for terminal lugs and in-line splices Applicable EN 2591-218 Ageing of terminal lugs and in-line splices by temperature and current cycling 1 500 cycles - Temperature 150 C a EN 2591-219 Voltage strength for insulated terminal lugs and in-line splices Not applica

36、ble EN 2591-301 Endurance at temperature 120 hours at 165 C EN 2591-305 Rapid change of temperature EN 2591-101 and EN 2591-217 EN 2591-307 Salt mist Applicable EN 2591-314 Immersion at low air pressure Not applicable EN 2591-315 Fluid resistance Not applicable EN 2591-403 Sinusoidal and random vibr

37、ation Applicable EN 2591-417 Tensile strength (crimped connection) Applicable EN 3373-001 Crimping at low temperature Applicable EN 3373-001 Sleeve strength Not applicable EN 3373-001 Flammability Not applicable a The current and application time used to achieve the specified upper temperature durin

38、g the first cycle is to be used for all subsequent cycles 8 Details of assembly tooling 8.1 Crimping tools Crimping tools shall conform to the requirements of MIL-DTL-22520. For conductors up to size 050 the crimping tool used shall be M22520/5-01 and, for conductor sizes from 090 and above, tools c

39、onforming to MS25441. 8.2 Die dimensions For conductor sizes up to 050 the dimensions of the dies shall conform to the dimensions size 090 and larger shall conform to MS90485. 9 Marking The item code as per Table 1 and the manufacturers monogram shall be embossed in the marking area shown in Figure 1 in accordance with EN 2424 Style F. 10 Packaging The packaging shall be marked with the EN designation, manufacturers name, part number, quantity in the package, date of manufacturer and batch number.