BS EN 3745-506-2009 航空航天系列.飞行器用光纤和电缆.抗冲击能力试验方法.pdf

《BS EN 3745-506-2009 航空航天系列.飞行器用光纤和电缆.抗冲击能力试验方法.pdf》由会员分享，可在线阅读，更多相关《BS EN 3745-506-2009 航空航天系列.飞行器用光纤和电缆.抗冲击能力试验方法.pdf（8页珍藏版）》请在三一文库上搜索。

1、 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3745-506 August 2009 ICS 49.060 English Version Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 506: Impact resistance Srie arospatiale - Fibres et cbles optiques usage aronautique - Mthodes dessais - Partie 506:

2、 Rsistance limpact Luft- und Raumfahrt - Faseroptische Leitungen fr Luftfahrzeuge - Prfverfahren - Teil 506: Schlagfestigkeit This European Standard was approved by CEN on 3 July 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving

3、 this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versi

4、ons (English, French, German). A version in any other language made by translation under the respons bility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,

5、 Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STA

6、NDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3745-506:2009: E EN 3745-506:2009 (E) 2 Contents P

7、age Foreword 3 1 Scope 4 2 Normative references 4 3 Preparation of specimens .4 4 Apparatus .4 5 Method 5 5.1 Procedure .5 5.2 Final measurements and requirements .5 EN 3745-506:2009 (E) 3 Foreword This document (EN 3745-506:2009) has been prepared by the Aerospace and Defence Industries Association

8、 of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re- ceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This Eur

9、opean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2010, and conflicting national standards shall be withdrawn at the latest by February 2010. Attention is drawn to the possibility that some of the

10、elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement thi

11、s European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Repub- lic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and th

12、e United Kingdom. EN 3745-506:2009 (E) 4 1 Scope This standard specifies a method to determine the ability of an optical fibre or cable to withstand impact under specified environmental conditions. 2 Normative references The following referenced documents are indispensable for the application of thi

13、s document. For dated refer- ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3745-100, Aerosp

14、ace series Fibres and cables, optical, aircraft use Test methods Part 100: General EN 3745-201, Aerospace series Fibres and cables, optical, aircraft use Test methods Part 201: Visual inspection EN 3745-301, Aerospace series Fibres and cables, optical, aircraft use Test methods Part 301: Attenuation

15、 EN 187000, Generic specification: Optical fibre cables 3 Preparation of specimens 3.1 lf not at standard test conditions, the specimens shall be subjected to standard test conditions and sta- bilized at these conditions for 24 h as defined in EN 3745-100. Attenuation should be measured, in accor- d

16、ance with EN 3745-301 method C, before the test. 3.2 Unless otherwise specified in the product standard, the following details shall be as stated in the tech- nical specification: a) the temperature at which test is carried out if other than standard; b) the number and length of specimens; c) the ma

17、ss of the weight and the drop height, or alternatively the impact energy; d) the radius R of the intermediate piece; e) the number of impacts; f) the permissible change in attenuation after the test. 4 Apparatus The apparatus shall comprise: a) a Light Launch System (LLS) and Light Detector System (

18、LDS) as defined in EN 2591-100; b) impact test apparatus as defined in EN 187000 method 505. The impact test apparatus shall permit a weight to drop vertically onto an intermediate piece of steel which transmits the impact to the cable sample. The sample shall be fixed to a flat substantial steel ba

19、se. EN 3745-506:2009 (E) 5 5 Method 5.1 Procedure After the cable sample has been mounted in the test apparatus, the attenuation shall be measured as defined in EN 3745-301, method C. The mass of the weight and the height from which the weight falls be as specified, or if an impact energy is specifi

20、ed shall be adjusted to give the value of impact energy shown. The number of impacts shall be as specified. The attenuation shall be measured immediately after the test as defined in EN 3745-301, method C. 5.2 Final measurements and requirements A visual examination shall be carried out as defined in EN 3745-201. The attenuation change shall be less than the specified value.