BS EN 1597-3-1997 Welding consumables D Test methods Part 3. Testing of positional capability of welding consumables in a fillet weld.pdf
《BS EN 1597-3-1997 Welding consumables D Test methods Part 3. Testing of positional capability of welding consumables in a fillet weld.pdf》由会员分享,可在线阅读,更多相关《BS EN 1597-3-1997 Welding consumables D Test methods Part 3. Testing of positional capability of welding consumables in a fillet weld.pdf(10页珍藏版)》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1597-3 : 1997 The E
2、uropean Standard EN 1597-3 : 1997 has the status of a British Standard ICS 25.160.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Welding consumables Test methods Part 3. Testing of positional capability of welding consumables in a fillet weld This British Standard, having
3、been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1997 BSI 1997 ISBN 0 580 28634 7 BS EN 1597-3 : 1997 Amendments issued since publication Amd. No.DateText affected National foreword This B
4、ritish Standard is the English language version of EN 1597-3 : 1997. The UK participation in its preparation was entrusted to Technical Committee WEE/39 which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpret
5、ation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which i
6、mplement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Compliance with a British Standar
7、d does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. CEN European Committee for Standardization Comite Europe en de Normalisation Europa isch
8、es Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 All rights of exploitation in any form and by any means reserved worldwide for CEN national members Ref. No. EN 1597-3 : 1997 E EUROPEAN STANDARDEN 1597-3 NORME EUROPE ENNE EUROPA ISCHE NORM July 1997 ICS 25.160.20
9、 Descriptors: Welding, arc welding, fillet welds, steels, nickel, nickel alloys, fillers, covered electrodes, joining, preparation, test specimen, tests, visual examination, weld defects English version Welding consumables Test methods Part 3: Testing of positional capability of welding consumables
10、in a fillet weld Produits consommables pour le soudage Me thodes dessai Partie 3: Evaluation de laptitude des produits consommables a la re alisation de soudures dangle en position Schweizusa tze Pru fmethoden Teil 3: Pru fung de Eignung fu r Schweipositionen an Kehlnahtschweiungen This European Sta
11、ndard was approved by CEN on 1997-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning suc
12、h national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language
13、and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switz
14、erland and United Kingdom. Page 2 EN 1597-3 : 1997 BSI 1997 Foreword This European Standard has been prepared by Technical Committee CEN/TC 121, Welding, the secretariat of which is held by DS. This European Standard shall be given the status of a national standard, either by publication of an ident
15、ical text or by endorsement, at the latest by January 1998, and conflicting national standards shall be withdrawn at the latest by January 1998. This standard consists of the following Parts: Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys Part 2: Preparation
16、of test piece for single-run and two-run technique test specimens in steel Part 3: Testing of positional capability of welding consumables in a fillet weld According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this E
17、uropean Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 Introduction3 1Scope3 2Normative references3 3General requirem
18、ents3 4Test plate material3 5Preparation of the test piece3 6Examination of the fillet weld3 7Test report4 Page 3 EN 1597-3 : 1997 BSI 1997 Introduction This standard describes preparation and assessment of a fillet weld test piece. Test conditions prescribed and results required should not be consi
19、dered to be requirements or expectations for a procedure qualification. 1 Scope This standard specifies the preparation of the test piece and the evaluation of the test results. The purpose of this standard is to test positional capability of covered electrodes and tubular cored electrodes. Fillet w
20、elds can be made in horizontal, vertical up, vertical down and overhead position, as applicable. NOTE. If results complying with the requirements of this standard have been achieved in a procedure qualification or type approval test, the welding consumable is regarded as tested in accordance with th
21、is standard. This standard is applicable to consumables for arc welding of steel. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publicati
22、ons are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 499Welding co
23、nsumables Covered electrodes for manual metal arc welding of non alloy and fine grain steels Classification EN 758Welding consumables Tubular cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels Classification EN 970Non-destructive examination of fu
24、sion welds Visual examination EN ISO 6947Welds Working positions Definitions of angles of slope and rotation (ISO 6947 : 1993) EN 25817Arc-welded joints in steel Guidance on quality levels for imperfections (ISO 5817 : 1992) 3 General requirements Welding consumables to be tested shall be representa
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1597-3-1997 Welding consumables Test methods Part 3. Testing of positional capability in fillet 1597
链接地址:https://www.31doc.com/p-3644291.html