AS 60034-8-2009 Rotating electrical machines Part 8 Terminal markings and direction of rotation.pdf
《AS 60034-8-2009 Rotating electrical machines Part 8 Terminal markings and direction of rotation.pdf》由会员分享,可在线阅读,更多相关《AS 60034-8-2009 Rotating electrical machines Part 8 Terminal markings and direction of rotation.pdf(40页珍藏版)》请在三一文库上搜索。
1、 AS 60034.82009 Australian Standard Rotating electrical machines Part 8: Terminal markings and direction of rotation (IEC 60034-8, Ed. 3 (2007) MOD) AS 60034.82009 This Australian Standard was prepared by Committee EL-009, Rotating Electrical Machinery. It was approved on behalf of the Council of St
2、andards Australia on 11 June 2009. This Standard was published on 15 July 2009. The following are represented on Committee EL-009: Airconditioning and Refrigeration Equipment Manufacturers Association of Australia Australian Chamber of Commerce and Industry Australian Electrical and Electronic Manuf
3、acturers Association Australian Greenhouse Office, Department of the Environment and Water Resources Australian Industry Group Bureau of Steel Manufacturers of Australia Department of Defence (Australia) Electrical Apparatus Service Association Energy Efficiency and Conservation Authority of New Zea
4、land Engineers Australia Ministry of Economic Development (New Zealand) Registered Master Builders This Standard was issued in draft form for comment as DR 08206. Standards Australia wishes to acknowledge the participation of the expert individuals that contributed to the development of this Standar
5、d through their representation on the Committee and through the public comment period. Keeping Standards up-to-date Keeping Standards up-to-date Australian Standards are living documents that reflect progress in science, technology and systems. To maintain their currency, all Standards are periodica
6、lly reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments that may have been published since the Standard was publish
7、ed. Detailed information about Australian Standards, drafts, amendments and new projects can be found by visiting www.standards.org.auwww.standards.org.au Standards Australia welcomes suggestions for improvements, and encourages readers to notify us immediately of any apparent inaccuracies or ambigu
8、ities. Contact us via email at mailstandards.org.aumailstandards.org.au, or write to Standards Australia, GPO Box 476, Sydney, NSW 2001. The Standard is downloaded from Standard Sharing AS 60034.82009 Australian Standard Rotating electrical machines Part 8: Terminal markings and direction of rotati
9、on (IEC 60034-8, Ed. 3 (2007) MOD) Originated as AS 1359.31982. Revised and redesignated AS 60034.82009. COPYRIGHT Standards Australia All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the
10、written permission of the publisher. Published by Standards Australia GPO Box 476, Sydney, NSW 2001, Australia ISBN 0 7337 9190 5 ii PREFACE This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee EL-009, Rotating Electrical Machinery to supersede AS 1359.31982, R
11、otating electrical machinesGeneral requirementsDirection of rotation and marking of terminals, on publication. This Standard was prepared by the Australian members of the Joint Standards Australia/Standards New Zealand Committee EL-009. After consultation with stakeholders in both countries, Standar
12、ds Australia and Standards New Zealand decided to develop this Standard as an Australian Standard rather than an Australian/New Zealand Standard. The objective of this Standard is to provide uniform rules in electrical connections and marking of rotating electrical machines. This Standard is an adop
13、tion with national modifications and has been reproduced from IEC 60034-8, Ed. 3 (2007), Rotating electrical machines Part 8: Terminal markings and direction of rotation. Variations to IEC 60034-8, Ed. 3 (2007) are indicated at the appropriate places throughout this Standard. Strikethrough (example)
14、 identifies IEC text, tables and figures which, for the purposes of this Australian Standard, are deleted. Where text, tables or figures are added, each is set in its proper place and identified by shading (example). Added figures are not themselves shaded, but are identified by a shaded border. Thi
15、s Standard is Part 8 of a Series dealing with rotating electrical machinery. Additional parts will be added from time to time. This Series when complete will consist of the following parts: AS 1359.102.2 Rotating electrical machinesMethods for determining losses and efficiency of rotating electrical
16、 machinery from testsMeasurement of losses by the calorimetric method 60034 Rotating electrical machines 60034.1 Part 1: Rating and performance 60034.2.1 Part 2.1: Methods for determining losses and efficiency from tests (excluding machines for traction vehicles) 60034.3 Part 3: Specific requirement
17、s for synchronous generators driven by steam turbines or combustion gas turbines 60034.4 Part 4: Methods for determining synchronous machine quantities from tests 60034.5 Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code)Classification 60034.6 Par
18、t 6: Method of cooling (IC code) 60034.7 Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM code) 60034.8 Part 8: Terminal markings and direction of rotation (this Standard) 60034.9 Part 9: Noise limits 60034.11 Part 11: Thermal protection 60034.12 P
19、art 12: Starting performance of single-speed three-phase cage induction motors 60034.14 Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higherMeasurement, evaluation and limits of vibration severity 60034.15 Part 15: Impulse voltage withstand levels of rotating a.c. ma
20、chines with form- wound stator coils 60034.16 Part 16: Excitation systems for synchronous machines (all parts) 60034.17 Part 17: Cage induction motors when fed from convertersApplication guide 60034.18 Part 18: Functional evaluation of insulation systems (all parts) The Standard is downloaded from
21、Standard Sharing iii AS 60034.19 Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies 60034.20.1 Part 20.1: Control motorsStepping motors 60034.22 Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets 60034.23 Part 23:
22、 Specification for the refurbishing of rotating electrical machines 60034.25 Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply 60034.26 Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors 60034.27 Pa
23、rt 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines 60034.28 Part 28: Test methods for determining quantities of equivalent circuit diagrams for the three-phase low voltage cage induction motors 60034.29 Part 29: Equivalent loading and supe
24、rposition techniquesIndirect testing to determine temperature rise As this Standard is reproduced from an International Standard, the following applies: (a) Its number does not appear on each page of text and its identity is shown only on the cover and title page. (b) In the source text IEC 60034-8
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AS 60034-8-2009 Rotating electrical machines Part Terminal markings and direction of rotation 60034 2009
链接地址:https://www.31doc.com/p-3645249.html