BS EN 1013-1-1998 Light transmitting profiled plastic sheeting for single skin roofing Part 1 General requirements and test methods.pdf
《BS EN 1013-1-1998 Light transmitting profiled plastic sheeting for single skin roofing Part 1 General requirements and test methods.pdf》由会员分享,可在线阅读,更多相关《BS EN 1013-1-1998 Light transmitting profiled plastic sheeting for single skin roofing Part 1 General requirements and test methods.pdf(18页珍藏版)》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1013-1:1998 The Eur
2、opean Standard EN 1013-1:1997 has the status of a British Standard ICS 83.140.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Light transmitting profiled plastic sheeting for single skin roofing Part 1: General requirements and test methods This British Standard, having bee
3、n prepared under the direction of the Sector Board for Building and Civil Engineering, was published under the authority of the Standards Board and comes into effect on 15 April 1998 BSI 1998 ISBN 0 580 29633 4 BS EN 1013-1:1998 Amendments issued since publication Amd. No.DateText affected National
4、foreword This British Standard is the English language version of EN 1013-1:1997. The UK participation in its preparation was entrusted by Technical Committee B/542, Roofing and cladding products for discontinuous laying, to Subcommittee B/542/8, Light transmitting plastics sheeting for roofing and
5、cladding, which has the responsibility to: aid enquirers to understand the text; present to the responsible internationl/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and pr
6、omulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under
7、the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicat
8、ion. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 15 and a back cover. CEN European Committee for Standardization Comite Europe en de Normalis
9、ation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1013-1:1997 E EUROPEAN STANDARDEN 1013-1 NORME EUROPE ENNE EUROPA ISCHE NORM Nov
10、ember 1997 ICS 83.140.10 Descriptors: Roofing, plates, ribbed sheets, plastic products, light transmission, specifications, appearance, shock resistance, ageing: materials, dimensional tolerances, tests, measurements, marking English version Light transmitting profiled plastic sheeting for single sk
11、in roofing Part 1: General requirements and test methods Plaques profile es e clairantes en matie re plastique pour couverture en simple paroi Partie 1: Exigences ge ne rales et me thodes dessai Lichtdurchla ssige profilierte Platten aus Kunststoff fu r einschalige Dacheindeckungen Teil 1: Allgemein
12、e Anforderungen und Pru fverfahren This European Standard was approved by CEN on 2 November 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to
13、-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under
14、the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemb
15、ourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Page 2 EN 1013-1:1997 BSI 1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 128, Roof covering products for discontinuous laying and products for wall cladding, the Secretariat of w
16、hich is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at the latest by May 1998. According to the CEN/CENELEC Interna
17、l Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland an
18、d the United Kingdom. Contents Page Foreword2 Introduction3 1Scope3 2Normative references3 3Definitions3 4Symbols and abbreviations4 5Requirements4 6Test methods5 7Ageing procedure and measurement after ageing (type test)9 8Marking, labelling, packaging10 Annex A (normative) Profile terminology15 Pa
19、ge 3 EN 1013-1:1997 BSI 1998 Introduction This standard describes the general requirements and test methods for translucent roofing sheets. The physical properties of translucent profiled plastic sheets differ from bituminous, metal and fibre reinforced cement sheets, as defined in EN 534, prEN 506,
20、 prEN 508-1, prEN 508-2, prEN 508-3 or EN 494. They do not necessarily have the same span capabilities and alternative fixing specifications are generally required. Until codes of practice are established, determination of span capabilities and/or method of fixing is based on specific test results.
21、Reference should be made to national codes and/or manufacturers literature for requirements concerning design, storage and installation, including all safety aspects, according to material. 1 Scope This European Standard specifies the general requirements for profiled plastic translucent sheets for
22、single skin roofing irrespective of the material used to produce the sheets. The specific requirements according to the material itself are given in specific parts of this standard, e.g. prEN 1013-2 and EN 1013-3. The standard specifies test methods and each (excepting that for dimensional tolerance
23、s) is defined either as a type test or a quality control test. The test method for dimensional tolerances has been included to provide a common approach for the purchaser and the manufacturer in cases of dispute over measurements. This standard is applicable to all types of translucent roofing sheet
24、s used in any kind of buildings. NOTEMaterial complying with this standard is also applicable for single skin vertical cladding. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the a
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1013-1-1998 Light transmitting profiled plastic sheeting for single skin roofing Part General requirements 1013
链接地址:https://www.31doc.com/p-3645282.html