BS EN 10163-1-2004 热轧钢板材、宽扁材和型材表面条件供货要求规范.第1部分一般要求.pdf
《BS EN 10163-1-2004 热轧钢板材、宽扁材和型材表面条件供货要求规范.第1部分一般要求.pdf》由会员分享,可在线阅读,更多相关《BS EN 10163-1-2004 热轧钢板材、宽扁材和型材表面条件供货要求规范.第1部分一般要求.pdf(16页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10163-1:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements The European Standard EN 10163-1:2004 has the status of a British Standard ICS 77.140.50 ? Licensed Copy: London South Bank University, Lon
2、don South Bank University, Fri Mar 24 04:47:25 GMT 2006, Uncontrolled Copy, (c) BSI BS EN 10163-1:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 December 2004 BSI 16 December 2004 ISBN 0 580 45121 6 National foreword This British Sta
3、ndard is the official English language version of EN 10163-1:2004. It supersedes BS EN 10163-1:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/12, Structural steels, which has the responsibility to: A list of organizations represented on this
4、 committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “ International Standards Correspondence Index” , or by usin
5、g the “ Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity f
6、rom legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in th
7、e UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 13 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed
8、Copy: London South Bank University, London South Bank University, Fri Mar 24 04:47:25 GMT 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10163-1 December 2004 ICS 77.140.50Supersedes EN 10163-1:1991 English version Delivery requirements for surface condition of
9、 hot-rolled steel plates, wide flats and sections - Part 1: General requirements Conditions de livraison relatives ltat de surface des tles, larges plats et profils en acier lamins chaud - Partie 1: Gnralits Lieferbedingungen fr die Oberflchenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech
10、, Breitflachstahl und Profile) - Teil 1: Allgemeine Anforderungen This European Standard was approved by CEN on 4 November 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar
11、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other lang
12、uage made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
13、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Mana
14、gement Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10163-1:2004: E Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:47:25 GMT 2006, Uncont
15、rolled Copy, (c) BSI EN 10163-1:2004 (E) 2 Contents Page Foreword3 1Scope 4 2Normative references4 3Terms and definitions .4 4General4 5Classification5 6Requirements.5 6.1Depth and affected area of discontinuities.5 6.1.1Depth.5 6.1.2Affected area5 6.2Repair requirements8 6.3Repair procedures.8 6.3.
16、1Grinding8 6.3.2Welding.8 Annex A (informative) Description of most common discontinuities9 Annex B (informative) List of equivalent terms in foreign languages .11 Annex C (informative) List of national standards which correspond with EURONORMS referenced.12 Bibliography13 Licensed Copy: London Sout
17、h Bank University, London South Bank University, Fri Mar 24 04:47:25 GMT 2006, Uncontrolled Copy, (c) BSI ? EN 10163-1:2004 (E) 3 Foreword This document (EN 10163-1:2004) has been prepared by Technical Committee ECISS/TC 10 “Structural steels Grades and qualities”, the secretariat of which is held b
18、y NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. This document supersedes EN 10163-1:1991, Delive
19、ry requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements. This document covers the general delivery requirements for the surface condition of hot-rolled steel products such as: plates and wide flats, see Part 2; sections, see Part 3. Duri
20、ng the 5 year review of EN 10163-1:1991 the members of ECISS/TC 10 agreed to revise EN 10163- 1:1991. It was asked to bring the text in line with ECISS DOCS N 809 “Iron and steel standardization Model for a product standard”. This document includes a Bibliography. According to the CEN/CENELEC Intern
21、al Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl
22、ands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:47:25 GMT 2006, Uncontrolled Copy, (c) BSI ? EN 10163-1:2004 (E) 4 1 Scope 1.1 This document specifies the gener
23、al requirements for the surface condition of hot-rolled steel plates, wide flats and sections. It covers the requirements on the type, the permissible depth and the permissible size of the surface area affected by: discontinuities (imperfections and defects) and repairs by grinding and/or welding. 1
24、.2 This document shall be applied so far as no other requirements for the surface condition exist in the appropriate material or product standard. The requirements laid down in the appropriate material or product standard shall always prevail. 2 Normative references The following referenced document
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10163-1-2004 热轧钢板材、宽扁材和型材表面条件供货要求规范.第1部分一般要求 10163 2004 轧钢 板材 宽扁材 表面 条件 供货 要求 规范 部分 一般
链接地址:https://www.31doc.com/p-3645285.html