AS 2885-1-2009 Pipelines—Gas and liquid petroleum Part 1 Design and construction.pdf

《AS 2885-1-2009 Pipelines—Gas and liquid petroleum Part 1 Design and construction.pdf》由会员分享，可在线阅读，更多相关《AS 2885-1-2009 Pipelines—Gas and liquid petroleum Part 1 Design and construction.pdf（304页珍藏版）》请在三一文库上搜索。

1、 AS 2885.12007 (Incorporating Amendment No. 1) Australian Standard PipelinesGas and liquid petroleum Part 1: Design and construction AS 2885.12007 This Australian Standard was prepared by Committee ME-038, Petroleum Pipelines. It was approved on behalf of the Council of Standards Australia on 19 Jan

2、uary 2007. This Standard was published on 25 May 2007. The following are represented on Committee ME-038: APIA Research and Standards Committee Australasian Corrosion Association Australian Chamber of Commerce and Industry Australian Institute of Petroleum Australian Pipeline Industry Association Bu

3、reau of Steel Manufacturers of Australia Department of Consumer and Employment Protection (WA) Department of Energy, Utilities and Sustainability (NSW) Department of Mines and Energy (Qld) Department of Primary Industries (Victoria) Department of Primary Industry, Fisheries and Mines (NT) Energy Net

4、works Association Gas Association of New Zealand Primary Industries and Resources SA Welding Technology Institute of Australia This Standard was issued in draft form for comment as DR 04561. Standards Australia wishes to acknowledge the participation of the expert individuals that contributed to the

5、 development of this Standard through their representation on the Committee and through the public comment period. Keeping Standards up-to-date Keeping Standards up-to-date Australian Standards are living documents that reflect progress in science, technology and systems. To maintain their currency,

6、 all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments that may have been published si

7、nce the Standard was published. Detailed information about Australian Standards, drafts, amendments and new projects can be found by visiting www.standards.org.auwww.standards.org.au Standards Australia welcomes suggestions for improvements, and encourages readers to notify us immediately of any app

8、arent inaccuracies or ambiguities. Contact us via email at mailstandards.org.aumailstandards.org.au, or write to Standards Australia, GPO Box 476, Sydney, NSW 2001. The Standard is downloaded from Standard Sharing AS 2885.12007 (Incorporating Amendment No. 1) Australian Standard PipelinesGas and li

9、quid petroleum Part 1: Design and construction First published in part as part of AS CB281972. Revised and redesignated AS 16971975. AS 1958 first published 1976. AS 2018 first published 1977. Second edition AS 16971979. Third edition 1981. Second edition AS 19581981. Second edition AS 20181981. AS

10、19581981 and parts of AS 16971981 and AS 20181981 revised, amalgamated and redesignated AS 28851987. Parts of AS 16971981, AS 20181981 and AS 28851987 revised, amalgamated and redesignated in part as AS 2885.11997. Second edition 2007. Reissued incorporating Amendment No. 1 (February 2009). COPYRIGH

11、T Standards Australia All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. Published by Standards Australia GPO Box 476, Sydney, NSW 2001, Australia IS

12、BN 0 7337 8241 8 AS 2885.12007 2 PREFACE This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee ME-038, Petroleum Pipelines, to supersede AS 28851997, PipelineGas and liquid petroleum. This Standard incorporates Amendment No. 1 (February 2009). The changes requir

13、ed by the Amendment are indicated in the text by a marginal bar and amendment number against the clause, note, table, figure or part thereof affected. After consultation with stakeholders in both countries, Standards Australia and Standards New Zealand decided to develop this Standard as an Australi

14、an Standard rather than an Australian/New Zealand Standard. The objective of this Standard is to provide requirements for the design and construction of steel pipelines and associated piping and components that are used to transmit single phase and multi-phase hydrocarbon fluids. This standard provi

15、des guidelines for use of pipe manufactured from certain non steel or corrosion-resistant materials. This Standard is part of a series, that covers high pressure petroleum pipelines, as follows: AS 2885 PipelinesGas and liquid petroleum 2885.0 Part 0: General requirements 2885.1 Part 1: Design and c

16、onstruction (this Standard) 2885.2 Part 2: Welding 2885.3 Part 3: Operation and maintenance 2885.4 Part 4: Submarine pipelines 2885.5 Part 5: Field pressure testing Text deleted Text deleted 2007 REVISION Text deleted The comprehensive revision of AS 2885.1 is the result of extensive work by subcomm

17、ittee ME-038-1 in response to a request from the industry that it consider increasing the design factor from 0.72 to 0.80. This request prompted a detailed review of each section and each clause of the Standard, resulting in the preparation of some 70 issue papers that considered the underlying tech

18、nical issues (in relation to an increased design factor) and recommended changes to the Standard. These issue papers were debated within the A1 A1 A1 A1 The Standard is downloaded from Standard Sharing 3 AS 2885.12007 subcommittee and published on the Industry web site to allow consideration by the

19、 Industry. The results of these deliberations form the basis of this revision. The revision also reflects the results of a significant and ongoing industry-funded research program undertaken by the Australian Pipeline Industry Association and its research contractors, and through its association wit

20、h the Pipeline Research Council International and the European Pipeline Research Group. This revision provides a basis for Industry to benefit through the application of an increased factor for pressure design (for new pipelines) and a structured basis for increasing the MAOP of a qualifying existin

21、g pipeline. These benefits are supported by robust requirements for safety, structural design, construction, testing and record keeping. Significant changes in this Revision include the following: (a) A restructure of the sections of the document to separate pipeline general, pipeline, stations, and

22、 instrumentation and control. (b) The incorporation of a section defining the minimum requirements for a pipeline whose maximum allowable operating pressure is proposed to be raised. (c) Section 2 (Safety) has been rewritten, to reflect experience gained in the seven years since it was revised to pr

23、ovide a mandatory requirement for risk assessment. This revision provides more explicit guidance on the obligation to undertake safety assessments with the integrity required for compliance with this Standard. Material is provided in normative and informative appendices. (d) Section 3 (Materials and

24、 components) has been revised to better address the treatment of materials used in pipelines. It includes a requirement to de-rate the specified minimum yield stress of pipe designed for operation at temperatures of 65C and higher. The use of fibreglass and corrosion-resistant alloy pipe materials f

25、or pipelines constructed to this Standard is permitted and limited in this Section. A minimum toughness requirement for pipe DN 100 and larger has been introduced. (e) Section 4 (Pipeline general) contains most of the material in the Pipeline general section of the 1997 revision. The Section has bee

26、n expanded to include the following: (i) A mandatory requirement for the design of a pipeline for the existing and intended land use. (ii) A revision of the requirements for effective pipeline marking including a change to require the marker sign to comply with a danger sign in accordance with AS 13

27、19, Safety signs for the occupational environment. (iii) A plan for isolation of a pipeline. (iv) Special requirements for pipelines constructed in locations where the consequence of failure by rupture is not acceptable. Provisions for compliance with these requirements for pipelines constructed to

28、this, or to an earlier revision of the Standard, in land where the location classification has changed to residential (or equal) is included. (v) The location classification definitions are revised and additional sub-classes are defined. (vi) The hydrostatic strength test pressure is redefined to ad

29、dress the situation where the pipe wall thickness exceeds the pressure design thickness, including corrosion allowance. (vii) Provisions for low-temperature excursions. (viii) Calculation methods for critical defect length, energy release rate and radiation contour. AS 2885.12007 4 (f) The requireme

30、nts for fracture control have been extensively revised to clarify the requirements and to reflect experience gained since 1997. Emphasis is placed on the use of the Battelle Two Curve model given the fact that most gas pipelines in Australia transport rich gas. (g) Section 5 (Pipeline design) has be

31、en revised to incorporate those provisions specific to pipeline in the 1997 revision. Significant changes to this Section include the following: (i) The pipe wall thickness is required to be the greater of the pressure design thickness, and the thickness required for each other identified load condi

32、tion. The thickness terms used in this Standard are clarified. (ii) An equation for calculating the thickness required for external pressure is provided. (iii) Recognizing the result of a comprehensive investigation, of its purpose and the impact of change, the design factor has been changed from 0.

33、72 to 0.80, and the design factor for pipeline assemblies and pipelines on bridges has been changed from 0.60 to 0.67. (iv) Text deleted (v) Requirements for stress and strain have been completely redrafted to clarify the requirements. The limits for each stress condition are tabulated and normative

34、 and informative appendices are provided incorporating the relevant equations. Reliability and limit state design methods are permitted for pipeline design and integrity analysis, using approved methods. (vi) The requirements for a prequalified design are included in a new clause. This is permitted

35、for short pipelines DN 200 and smaller with a MAOP of 10.2 MPa or less. (vii) The provisions for reduced cover for a pipeline constructed through rock have been revised. (viii) The method for calculating reinforcement of branch connections in AS 2885.11987 has been reinstated in full. (h) Section 6

36、(Station design) incorporates the provisions of Clause 4.4 of the 1997 revision in relation to stations. The Section has been expanded to require the Design Basis for stations to be documented. Additional guidance is provided on treatment of lightning, together with some clarifying revisions to the

37、text. (i) Section 7 (Instrumentation and control design) incorporates the requirements of Clause 4.2 of the 1997 revision. The requirements for pipeline operation under transient conditions and a tolerance specification for pressure controls on pipelines intended to be operated at MAOP are addressed

38、. (j) Section 8 (Corrosion mitigation) incorporates the requirements of Section 5 of the 1997 revision. The Section incorporates clarifying revisions. (k) Section 9 (Upgrade of MAOP) is a new Section that sets down the minimum process, including activities required, to demonstrate the fitness of a p

39、ipeline designed and operated at one pressure as suitable for approval for operation at a higher pressure. The Section establishes a structured methodology for demonstrating the pipeline fitness and, once approved, for commissioning the pipeline at the new pressure. The maximum pressure is limited t

40、o the hydrostatic strength test pressure divided by the equivalent test pressure factor. A1 A1 The Standard is downloaded from Standard Sharing 5 AS 2885.12007 (l) Section 10 (Construction) incorporates Section 6 of the 1997 Standard. The requirements for construction survey are clarified, and a mi

41、nimum accuracy for as- constructed survey is incorporated. Since padding and backfilling are two activities that impact on the pipeline integrity, this revision incorporates additional requirements for these activities reflecting outcomes from APIA research on backfilling. (m) Section 11 (Inspection

42、 and testing) has been revised to align it with the requirements of AS 2885.5. It specifies strength test endpoint requirements for pipelines with a pressure design factor of 0.80, and references APIA research and associated software designed to enable the analysis of the pipe in a proposed (and con

43、structed) test section to be analysed to determine the presence and location of pipe that may be exposed to excessive strain at the intended strength test pressure. (n) Section 12 (Documentation). Obligations on the developer of a new pipeline to document the design and construction, and to transfer

44、 this information to the pipeline operator, are clarified and expanded. (o) Each appendix in the 1997 revision of the Standard has been critically reviewed and revised, as appropriate. New appendices are provided reflecting the findings of APIA research, clarification of concepts in the Standard, an

45、d providing detailed calculation methods. (p) Resistance to penetration calculation methods and design requirements provided. In addition to the items identified above, there are a great many changes of lesser significance incorporated in the document to the extent that users should consider it as a

46、 familiar but new Standard. 2008 Amendment No. 1 Amendment No. 1 to AS 2885.12007 was prepared to correct errors in the 2007 revision and to clarify items identified as being potentially confusing. The amendment includes guidance on specifying fracture toughness when purchasing line pipe and include

47、s a simplified calculation for energy release from leaks. The requirements for the control of fracture initiation in components other than line pipe have been clarified. An informative Appendix, which provides guidance on the design, construction and testing of fibreglass pipelines, is included. The

48、 terms normative and informative have been used in this Standard to define the application of the appendix to which they apply. A normative appendix is an integral part of a Standard, whereas an informative appendix is only for information and guidance. Statements expressed in mandatory terms in not

49、es to tables and figures are deemed to be requirements of the Standard. A1 A1 AS 2885.12007 6 CONTENTS Page SECTION 1 SCOPE AND GENERAL 1.1 SCOPE 15 1.2 GENERAL 15 1.3 RETROSPECTIVE APPLICATION . 15 1.4 REFERENCED DOCUMENTS 16 1.5 DEFINITIONS 16 1.5.1 Accessory 16 1.5.2 Approved and approval 16 1.5.3 As low as reasonably practicable (ALARP). 16 1.5.4 Buckle 16 1.5.5 Casing 16 1.5.6 Collapse. 16 1.5.7 Competent person 16 1.5.8 Common threats. 16 1.5.9 Component.