AS NZS 3820-1998 Amdt 1-2004 Essential safety requirements for low voltage electrical equipment.pdf
《AS NZS 3820-1998 Amdt 1-2004 Essential safety requirements for low voltage electrical equipment.pdf》由会员分享,可在线阅读,更多相关《AS NZS 3820-1998 Amdt 1-2004 Essential safety requirements for low voltage electrical equipment.pdf(15页珍藏版)》请在三一文库上搜索。
1、AS/NZS 3820:1998 (Incorporating Amendment No. 1) Australian/New Zealand Standard Essential safety requirements for low voltage electrical equipment AS/NZS 3820 AS/NZS 3820:1998 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee QR-012, Conformance Marking to Regulat
2、ory Requirements. It was approved on behalf of the Council of Standards Australia on 2 September 1998 and on behalf of the Council of Standards New Zealand on 14 September 1998. It was published on 5 October 1998 The following are represented on Committee QR-012: Association of Certification Bodies
3、(Australia) Australian Chamber of Commerce and Industry Australian Communications Authority Australian Electrical and Electronic Manufacturers Association Australian Information Industry Association Australian Telecommunications Industry Association Committee for Plumbing Products Authorization (Aus
4、tralia) Consumer Electronics Suppliers Association (Australia) Department of Health and Family Services, Medical Devices Section, Therapeutic Goods Administration (Australia) Department of Primary Industries and Energy (Australia) Electrical Regulatory Authorities Council International Accreditation
5、 New Zealand Ministry of Commerce, Communications Division (New Zealand) Ministry of Commerce, Energy and Resources Division (New Zealand) National Association of Testing Authorities Australia New Zealand Association of Certifying Bodies New Zealand Manufacturers Federation Keeping Standards up-to-d
6、ate Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers
7、 assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Web Shop at .au or Standards New Zealand
8、web site at www.standards.co.nz and looking up the relevant Standard in the on-line catalogue. Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. For more frequent listings or notification of revisions, amendments and withdrawals, Standa
9、rds Australia and Standards New Zealand offer a number of update options. For information about these services, users should contact their respective national Standards organization. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediate
10、ly of any apparent inaccuracies or ambiguities. Please address your comments to the Chief Executive of either Standards Australia International or Standards New Zealand at the address shown on the back cover. This Standard was issued in draft form for comment as DR 97433. The Standard is downloaded
11、from Standard Sharing AS/NZS 3820:1998 (Incorporating Amendment No. 1) Australian/New Zealand Standard Essential safety requirements for low voltage electrical equipment First published as AS/NZS 3820:1998. Reissued incorporating Amendment No. 1 (January 2004). COPYRIGHT Standards Australia/Standar
12、ds New Zealand All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. Jointly published by Standards Australia International Ltd, GPO Box 5420, Sydney, N
13、SW 2001 and Standards New Zealand, Private Bag 2439, Wellington 6020 ISBN 0 7337 0345 3 AS/NZS 3820:1998 2 PREFACE This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee QR/012, Conformance Systems for Electrical and Plumbing Products, in response to a proposal f
14、rom the Electrical Regulatory Authorities Coordinating Committee. This Standard incorporates Amendment No. 1 (January 2004). The changes required by the Amendment are indicated in the text by a marginal bar and amendment number against the clause, note, table, figure or part thereof affected. The ob
15、jective of this Standard is to provide a set of outcomes-oriented criteria for the safety of electrical equipment, primarily for use by electrical regulators in relation to products for which regulatory approval before sale is not required (non-declared articles). For electrical equipment that is re
16、quired to be approved by regulators before being placed on the market (declared articles), there are specific regulatory requirements additional to the general requirements given in this Standard. The Standard is intended to be consistent with the criteria of the European Union low voltage directive
17、. In the preparation of this Standard, consideration was given to the following publications and acknowledgment is made of the assistance received: European Union low voltage directive. IEC Guide 104, The preparation of safety publications and the use of basic safety publications and group safety pu
18、blications. NZECP3, New Zealand Electrical Code of Practice for Electrical Safety of Fittings and Electrical Appliances This Standard is not a substitute for Standards that set out objective safety requirements based on testing. Rather it provides a high-level generic description of the safety outco
19、mes to be achieved and is intended to assist in providing a basis for regulatory uniformity. Specific product Standards provide measurable criteria that are regarded as ensuring that the outcomes described in this Standard will be met. The Standard is downloaded from Standard Sharing 3 AS/NZS 3820:
20、1998 CONTENTS Page 1 SCOPE .4 2 REFERENCED DOCUMENTS4 3 DEFINITIONS .4 4 SAFETY REQUIREMENTS 5 5 MEANS OF COMPLIANCE 8 A1 AS/NZS 3820:1998 4 COPYRIGHT STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Australian/New Zealand Standard Essential safety requirements for low voltage electrical equipment 1 SCOPE
21、This Standard sets out requirements for low voltage electrical equipment, to ensure that electrical equipment is constructed in accordance with good engineering practice in regard to safety such that it does not endanger the safety of persons (particularly children, the elderly and people with disab
22、ilities), domestic animals or property, when properly installed and maintained and used in applications for which it was made. 2 REFERENCED DOCUMENTS The following documents are referred to in this Standard: AS/NZS 3100 Approval and test specificationGeneral requirements for electrical equipment 311
23、2 Approval and test specificationPlugs and socket-outlets 4417 Marking of electrical products to indicate compliance with regulations 4417.1 Part 1: General rules for the use of the mark 4417.2 Part 2: Specific requirements for electrical safety regulatory applications 3350 Safety of household and s
24、imilar electrical appliances 3350.1 Part 1: General requirements 3 DEFINITIONS For the purpose of this Standard, the definitions below apply. 3.1 Certificate of approval A certificate that is issued by electrical regulators indicating approval for sale, based on testing to safety standards of an ele
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AS NZS 3820-1998 Amdt 1-2004 Essential safety requirements for low voltage electrical equipment 3820
链接地址:https://www.31doc.com/p-3645800.html