BS EN 1395-6-2007 Thermal spraying — Acceptance inspection of thermal spraying equipment —Part 6 Manipulator systems.pdf
《BS EN 1395-6-2007 Thermal spraying — Acceptance inspection of thermal spraying equipment —Part 6 Manipulator systems.pdf》由会员分享,可在线阅读,更多相关《BS EN 1395-6-2007 Thermal spraying — Acceptance inspection of thermal spraying equipment —Part 6 Manipulator systems.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1395-6:2007 Thermal spraying Acceptance inspection of thermal spraying equipment Part 6: Manipulator systems The European Standard EN 1395-6:2007 has the status of a British Standard ICS 25.220.20 ? BS EN 1395-6:2007 This British Standard was published under the authority of t
2、he Standards Policy and Strategy Committee on 28 February 2007 BSI 2007 ISBN 978 0 580 50281 1 National foreword This British Standard was published by BSI. It is the UK implementation of EN 1395-6:2007. This standard together with BS EN 1395-1, BS EN 1395-2, BS EN 1395-3, BS EN 1395-4, BS EN 1395-5
3、 and BS EN 1395-7 supersedes BS EN 1395:1996. The UK participation in its preparation was entrusted to Technical Committee STI/40, Thermally sprayed inorganic finishes. A list of organizations represented on STI/40 can be obtained on request to its secretary. This publication does not purport to inc
4、lude all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1395-6
5、January 2007 ICS 25.220.20Supersedes EN 1395:1996 English Version Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 6: Manipulator systems Projection thermique - Contrle dacceptation du matriel de projection thermique - Partie 6: Systme de manipulation Thermisches Spritze
6、n - Abnahmeprfungen fr Anlagen zum thermischen Spritzen - Teil 6: Handhabungssysteme This European Standard was approved by CEN on 23 December 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status o
7、f a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A ver
8、sion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, D
9、enmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMAL
10、ISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1395-6:2007: E EN 1395-6:2007 (E) 2 Contents Page Foreword3 1Scope 4 2Normative refer
11、ences4 3Terms and definitions .4 4Acceptance inspection4 5Manipulators for thermal spraying.4 6Designation 5 7Inspection report5 Annex A (informative) Inspection report for thermal spraying manipulator system (initial test/retest).6 Bibliography11 ? EN 1395-6:2007 (E) 3 Foreword This document (EN 13
12、95-6:2007) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the lat
13、est by July 2007, and conflicting national standards shall be withdrawn at the latest by July 2007. This document together with EN 1395-1, 1395-2, 1395-3, 1395-4 1395-5 and 1395-7 supersedes EN 1395:1996. EN 1395 consists of the following Parts, under the general title Thermal spraying Acceptance in
14、spection of thermal spraying equipment: Part 1: General requirements; Part 2: Flame spraying including HVOF; Part 3: Arc spraying; Part 4: Plasma spraying; Part 5: Plasma spraying in chambers; Part 6: Manipulator systems; Part 7: Powder feed systems. According to the CEN/CENELEC Internal Regulations
15、, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands
16、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. ? EN 1395-6:2007 (E) 4 1 Scope This European Standard specifies requirements for the acceptance inspection of thermal spraying equipment in this case manipulator systems used in spray jobs to prod
17、uce thermally sprayed coatings of reproducible quality. This part should be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedures. 2 Normative references The following referenced documents are indispensable for the application of this document. For da
18、ted references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 657:2005, Thermal spraying Terminology, classification 3 Terms and definitions For the purposes of this document, the terms and definitions giv
19、en in EN 657:2005 and the following apply. 3.1 manipulators equipment for horizontal and/or vertical repositioning and/or rotating of objects 4 Acceptance inspection 4.1 Purpose of acceptance inspection 5.1 to 5.4 reveal state of the art technology in thermal spraying equipment and the minimum requi
20、rements concerning accuracy of motion of a spraying gun and/or work piece as given in Annex A, Table A.2. 4.2 Preliminary conditions for inspection The manipulator system shall be installed according to the instructions of the manufacturer/supplier. It shall be completely fitted with any other manip
21、ulator equipment necessary for the spraying process, aligned, adjusted and shall be able to operate. Measurements see Annex A, Table A.1. 5 Manipulators for thermal spraying 5.1 General Generally, manipulators used for thermal spraying may move the gun and/or the work piece to be sprayed. Usually, m
22、anipulators used for thermal spraying do not need the same positioning accuracy as systems for positioning of tools when e.g. chip cutting on milling or drilling machines, due to a spreading of the spray spot as well as to masking of the area not to be sprayed. These circumstances allow larger toler
23、ances in positioning the spray gun and/or the work piece. ? EN 1395-6:2007 (E) 5 5.2 X-Y-Z gun manipulators X-Y-Z gun manipulators are often used instead of industrial robots. These manipulators provide less accuracy, repeatability and travel speed compared with industrial robots. Nevertheless, gun
24、manipulators are adequate for many typical spray jobs. Tolerances depend on application, spray process and work piece and should be agreed upon between the contracting parties. Typical values are given in Annex A. 5.3 Industrial robots Usually, industrial robots possess 5 axes or 6 axes. All movemen
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1395-6-2007 Thermal spraying Acceptance inspection of equipment Part Manipulator systems 1395
链接地址:https://www.31doc.com/p-3646332.html