BS EN 14592-2008 木结构.销型紧固件要求.pdf
《BS EN 14592-2008 木结构.销型紧固件要求.pdf》由会员分享,可在线阅读,更多相关《BS EN 14592-2008 木结构.销型紧固件要求.pdf(44页珍藏版)》请在三一文库上搜索。
1、- - - - - - - - - - W - - - - - - - 7- - * - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - W W D - - w - - - - - - - - - EN 14592:2008 (E) 2 Contents Page Foreword4 1 Scope 5 2 Normative references5 3 Terms and definitions .6 4 Symbols and abbreviations8 5 Dimensions and tolera
2、nces8 5.1 Method of measurement and accuracy.8 5.2 Length.8 5.3 Nominal diameter.8 5.4 Other dimensions 9 5.5 Cross-sectional area .9 6 Requirements.9 6.1 Nails 9 6.1.1 General9 6.1.2 Materials .9 6.1.3 Geometry9 6.1.4 Mechanical strength and stiffness.10 6.1.5 Corrosion protection.11 6.2 Staples 12
3、 6.2.1 General12 6.2.2 Materials .12 6.2.3 Geometry12 6.2.4 Mechanical strength and stiffness.12 6.2.5 Corrosion protection.13 6.3 Screws 13 6.3.1 General13 6.3.2 Materials .13 6.3.3 Geometry13 6.3.4 Mechanical strength and stiffness.14 6.3.5 Corrosion protection.15 6.4 Dowels 15 6.4.1 General15 6.4
4、.2 Materials .15 6.4.3 Geometry16 6.4.4 Mechanical strength and stiffness.16 6.4.5 Corrosion protection.16 6.5 Bolts and nuts16 6.5.1 General16 6.5.2 Materials .16 6.5.3 Geometry17 6.5.4 Mechanical strength and stiffness.17 6.5.5 Corrosion protection.17 7 Evaluation of conformity.18 7.1 General18 7.
5、2 Initial type testing (ITT) .18 7.2.1 General18 7.2.2 Sampling, testing and conformity criteria.18 7.3 Factory production control (FPC)23 - - - - - EN 14592:2008 (E) 3 7.3.1 General .23 7.3.2 Daily control.23 7.3.3 6-monthly control 29 8 Marking.30 8.1 General .30 8.2 Nails30 8.3 Staples30 8.4 Scre
6、ws30 8.5 Dowels31 8.6 Bolts and nuts31 Annex A (normative) Expression of corrosion protection specifications 32 Annex B (normative) Method of determining the torsion resistance to insertion of screws into timber33 Annex ZA (informative) Clauses of this European Standard addressing the provisions of
7、the EU Contruction Products Directive .35 Bibliography41 - - - - - EN 14592:2008 (E) 4 Foreword This document (EN 14592:2008) has been prepared by Technical Committee CEN/TC 124 “Timber structures”, the secretariat of which is held by SFS. This European Standard shall be given the status of a nation
8、al standard, either by publication of an identical text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by July 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ
9、ts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationshi
10、p with EC Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Re
11、public, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. - - - - - EN 14592:2008 (E) 5 1 Scope This Europe
12、an Standard specifies the requirements and test methods for materials, geometry, strength, stiffness and durability ascpects (i.e. corrosion protection) of dowel-type fasteners for use in load bearing timber structures. Only dowel-type fasteners manufactured from steel are covered by this European S
13、tandard. For the purpose of this standard, dowel-type fasteners for timber structures are taken to be nails, staples, screws, dowels, and bolts with nuts. Definitions of these items are given in Clause 3. This European Standard specifies also the evaluation of conformity procedures and includes requ
14、irements for marking of these products. This European Standard does not cover resin coated dowel-type fasteners and fasterners treated with fire retardants to improve their fire performance. It also does not cover resin coated fasteners. 2 Normative references The following referenced documents are
15、indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 409, Timber structures - Test methods - Determination of the yield moment of dowel ty
16、pe fasteners - Nails EN 1382, Timber structures - Test methods - Withdrawal capacity of timber fasteners EN 1383:1999, Timber structures - Test methods - Pull-through resistance of timber fasteners EN 1995-1-1:2004, Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules
17、 for buildings EN 10016 (all parts), Non-alloy steel rod for drawing and/or cold rolling EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels EN 10025-3, Hot rolled products of structural steels - Part 3: Technical delivery cond
18、itions for normalized/normalized rolled weldable fine grain structural steels EN 10083-1, Steels for quenching and tempering - Part 1: General technical delivery conditions EN 10083-2, Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels EN 10088-1, Stainle
19、ss steels - Part 1: List of stainless steels EN 10088-2, Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10149-1, Hot-rolled flat products made of high yield strength steels for cold forming Part 1: General deli
20、very conditions EN 10218-1, Steel wire and wire products - General - Part 1: Test methods EN 10230-1, Steel wire nails - Part 1: Loose nails for general applications EN 10278, Dimensions and tolerances of bright steel products - - - - - EN 14592:2008 (E) 6 EN 14358, Timber structures - Calculation o
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 14592-2008 木结构.销型紧固件要求 14592 2008 木结构 紧固 要求
链接地址:https://www.31doc.com/p-3646454.html