BS EN 1463-1-2009 Road marking materials — Retroreflecting road studs Part 1 Initial performance requirements.pdf
《BS EN 1463-1-2009 Road marking materials — Retroreflecting road studs Part 1 Initial performance requirements.pdf》由会员分享,可在线阅读,更多相关《BS EN 1463-1-2009 Road marking materials — Retroreflecting road studs Part 1 Initial performance requirements.pdf(28页珍藏版)》请在三一文库上搜索。
1、? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? BS EN 1463-1:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1463-1 March 2009 ICS 93.080.20Supersedes EN 1463-1:1997 English Version Road marking materials - Retroreflecting road studs - Part 1: Initial performance requirem
2、ents Produits de marquage routier - Plots rtrorflchissants - Partie 1 : Exigences initiales de performance Straenmarkierungsmaterialien - Markierungsknpfe - Teil 1: Anforderungen im Neuzustand This European Standard was approved by CEN on 17 February 2009. CEN members are bound to comply with the CE
3、N/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or
4、to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official vers
5、ions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S
6、pain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national
7、Members. Ref. No. EN 1463-1:2009: E BS EN 1463-1:2009 EN 1463-1:2009 (E) Contents Page Foreword 3 Introduction . 4 1Scope 5 2Normative references 5 3Terms and definitions . 5 4Types of road stud . 6 5Performance requirements . 7 5.1Construction . 7 5.2Dimensions . 7 5.3Night-time visibility 7 5.3.1P
8、hotometric requirements 7 5.3.2Colorimetric requirements 9 5.4Daytime visibility of temporary road studs . 10 5.5Resilience of depressible road studs 11 6Road stud fixing . 11 7Marking . 11 Annex A (normative) Test method for the determination of the coefficient of luminous intensity. 12 A.1General
9、12 A.2Apparatus . 12 A.3Procedure . 13 A.4Calculation and expression of results . 13 Annex B (normative) Test method for the determination of chromaticity co-ordinates of retroreflected radiation 15 B.1General 15 B.2Apparatus . 15 B.3Procedure . 15 B.4Calculation and expression of results . 15 Annex
10、 C (normative) Test method for the determination of chromaticity co-ordinates and luminance factor for daytime visibility . 17 C.1General 17 C.2Apparatus . 17 C.3Measurement and calculation 17 Annex D (normative) Test method for the determination of the resilience of depressible road studs 18 D.1App
11、aratus . 18 D.2Procedure . 18 D.3Evaluation of the test 18 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive 19 ZA.1 Scope and relevant characteristics 19 ZA.2 Procedure(s) for the attestation of conformity of retroreflecting
12、 road studs 20 ZA.2.1 System of attestation of conformity 20 ZA.2.2 Certificate and Declaration of Conformity 21 ZA.3 CE marking and labelling 22 Bibliography 25 ? BS EN 1463-1:2009 EN 1463-1:2009 (E) 3 Foreword This document (EN 1463-1:1997/A1:2009) has been prepared by Technical Committee CEN/TC 2
13、26 “ Road equipment” , the secretariat of which is held by AFNOR. This Amendment to the European Standard EN 1463-1:1997 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards
14、 shall be withdrawn at the latest by September 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard supersedes
15、 EN 1463-1:1997. The technical change incorporated in this revision is the Table ZA.1 in Annex ZA. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Cze
16、ch Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. ? BS EN 1463-1:2009 EN 1463-1:2009 (E) 4 Int
17、roduction In Mandate M/111, there is a clear requirement for durability in use. In order to meet this requirement, EN 1463-1 specifies, in Annex ZA Table ZA.1, the standard EN 1463-2 (Road test performance specifications). However, in the current Table ZA.1, the classes S0 and R0 (no performance det
18、ermined) are included (just as a way to reflect the result of the mentioned durability test, which requires 1-year of road exposure for the applicant studs) and some notified bodies have interpreted this as meaning that it is not required to test to EN 1463-2 and consequently CE marks are being gran
19、ted without durability being tested. However, in other cases, the mentioned test has been carried out; therefore, both types of road studs are now in the market granting a “ well different” class of CE-marking. In order to rectify this unsatisfactory situation it is proposed to amend the requirement
20、 for “ R” to become R1 to R4 - i.e. eliminating R0, which might have caused the confusion, and thus meaning that a road test has to be carried out and the requirement for durability is met. In addition, it is also proposed that the requirement for “ S” is deleted as this is not necessary to also hav
21、e this to ensure durability is tested. ? BS EN 1463-1:2009 EN 1463-1:2009 (E) 5 1 Scope This European Standard specifies the initial performance requirements and laboratory test methods for retroreflecting road studs intended for use as permanent and temporary road marking materials. 2 Normative ref
22、erences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1463-2:2000, Road marking materials Re
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1463-1-2009 Road marking materials Retroreflecting studs Part Initial performance requirements 1463
链接地址:https://www.31doc.com/p-3646458.html