BS EN 15067-2007 Plastics and rubber machines — Film converting machines for bags and sacks — Safety requirements.pdf
《BS EN 15067-2007 Plastics and rubber machines — Film converting machines for bags and sacks — Safety requirements.pdf》由会员分享,可在线阅读,更多相关《BS EN 15067-2007 Plastics and rubber machines — Film converting machines for bags and sacks — Safety requirements.pdf(36页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15067:2007 Plastics and rubber machines Film converting machines for bags and sacks Safety requirements ICS 83.200 - BS EN 15067:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2008 BSI 2008 ISBN 978 0 5
2、80 54759 1 National foreword This British Standard is the UK implementation of EN 15067:2007. The UK participation in its preparation was entrusted by Technical Committee MCE/3, Safeguarding of machinery, to Subcommittee MCE/3/2, Rubber and plastics machine Safety. A list of organizations represente
3、d on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/co
4、rrigenda issued since publication DateComments - e - - - - - - - - - - A- - - - - - - - - - - E - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - W W D - - - - - - - EN 15067:2007 (E) 2 Contents Page Foreword4 Introduction.5 1 Scope 6 2 Normative references7 3 Terms and definitions
5、 .8 4 List of significant hazards 11 4.1 General11 4.2 General hazards.11 4.2.1 Mechanical hazards.11 4.2.2 Electrical hazards 11 4.2.3 Slipping, tripping and falling hazards11 4.3 Unwind unit 12 4.4 Slit-welding unit.12 4.5 Gussetting unit.12 4.6 Lane deviation unit12 4.7 Perforating and welding or
6、 cutting and welding units.12 4.8 Blocking unit12 4.9 Pick-up and transfer units 13 4.10 Stacking unit 13 4.11 Punching unit.13 4.12 Folding unit 13 4.13 Winding unit.13 4.14 Labelling or taping unit.13 4.15 Handle and closure units13 4.16 Draw tape insertion unit13 4.17 Generators of electrostatic
7、charge13 4.18 Electrostatic discharge equipment13 5 Safety requirements and/or protective measures14 5.1 General14 5.2 General requirements14 5.2.1 Mechanical hazards.14 5.2.2 Electrical hazards 14 5.2.3 Slipping, tripping and falling hazards15 5.2.4 Hazards due to noise.15 5.2.5 Thermal hazards 16
8、5.2.6 Fire hazards16 5.2.7 Hazards during start-up and setting operations 16 5.3 Unwind unit 16 5.4 Slit-welding unit.17 5.5 Gussetting unit.17 5.6 Lane deviation unit17 5.7 Perforating and welding or cutting and welding units.17 5.8 Blocking unit18 5.9 Pick-up and transfer units 18 5.10 Stacking un
9、it 18 5.11 Punching unit.19 5.12 Folding unit 19 5.13 Winding unit.19 5.14 Labelling or taping unit.19 5.15 Handle and closure units19 - EN 15067:2007 (E) 3 5.16 Draw tape insertion unit20 5.17 Generators of electrostatic charge20 5.18 Electrostatic discharge equipment20 6 Verification of the safety
10、 requirements and/or protective measures 20 7 Information for use23 7.1 Minimum marking on the machine 23 7.2 Instruction manual 23 Annex A (normative) Noise test code.25 A.1 Introduction25 A.2 Determination of the A-weighted emission sound pressure level at the workstation.25 A.3 Determination of t
11、he A-weighted sound power level 25 A.4 Mounting and operating conditions26 A.5 Information to be recorded and reported26 A.5.1 General .26 A.5.2 General data.26 A.5.3 Mounting and operating conditions26 A.5.4 Standards.26 A.5.5 Noise data.26 A.6 Declaration and verification of noise emission values
12、.27 Annex B (informative) Relationship between the hazards and the safety requirements and/or protective measures28 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC.30 Annex ZB (informative) Relationship between this European
13、Standard and the Essential Requirements of EU Directive 2006/42/EC.31 Bibliography32 - EN 15067:2007 (E) 4 Foreword This document (EN 15067:2007) has been prepared by Technical Committee CEN/TC 145 “Plastics and rubber machines”, the secretariat of which is held by UNI. This European Standard shall
14、be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility that some of the elements of this document may
15、 be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU
16、 Directives. For relationship with EU Directives, see informative Annexes ZA and ZB, which are an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,
17、 Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. - EN 15067:20
18、07 (E) 5 Introduction This document is a type C standard as stated in EN ISO 12100-1. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those whi
19、ch are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. - EN 15067:2007 (E) 6 1 Scope This European Standard specifie
20、s the safety requirements applicable to the design and construction of film converting machines for making bags and sacks, for the significant and specific hazards listed in Clause 4. This type of machine is based on the welding process. A film converting machine for bags and sacks starts at the fil
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 15067-2007 Plastics and rubber machines Film converting for bags sacks Safety requirements 15067
链接地址:https://www.31doc.com/p-3646503.html