BS EN 14188-4-2009 嵌缝胶和密封剂.与接缝密封胶一起使用的涂底剂规范.pdf
《BS EN 14188-4-2009 嵌缝胶和密封剂.与接缝密封胶一起使用的涂底剂规范.pdf》由会员分享,可在线阅读,更多相关《BS EN 14188-4-2009 嵌缝胶和密封剂.与接缝密封胶一起使用的涂底剂规范.pdf(14页珍藏版)》请在三一文库上搜索。
1、 W - - - - - - - - - - - 7- - - -7- - - - - - $ - $ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - W W D - w - - - - EN 14188-4:2009 (E) 2 Contents Page Foreword 3 1Scope 4 2Normative references 4 3Terms and definitions .4 4Types .5 5Requirements .5 5.1Homogeneity 5 5.2Density 5
2、 5.3Viscosity .5 5.4Resistance against alkali 5 5.5Evaporation behaviour of volatiles 5 5.6Solid content 5 5.7Flash point 6 5.8Softening point of solids .6 5.8.1Bitumen based primers .6 5.8.2Resin based primers .6 5.9Dangerous substances .6 6Evaluation of conformity .6 6.1General 6 6.2Type testing 6
3、 6.2.1Initial Type Testing 6 6.2.2Further type testing .7 6.3Factory Production Control (FPC) .7 6.3.1General 7 6.3.2Frequency of testing .7 6.3.3Equipment 7 6.3.4Raw materials and components .7 6.3.5Design process 7 6.3.6Non-conforming products 7 7Marking, labelling and packaging 8 7.1General 8 7.2
4、Primer 8 7.3Containers 8 Annex A (normative) Initial Type Testing and frequencies of testing for Factory Production Control .9 Annex B (informative) Example of a product data sheet 10 EN 14188-4:2009 (E) 3 Foreword This document (EN 14188-4:2009) has been prepared by Technical Committee CEN/TC 227 “
5、Road Materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by Janua
6、ry 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard is one of a series of standards as listed below: EN 14
7、188-1, Joint fillers and sealants Part 1: Specifications for hot applied sealants; EN 14188-2, Joint fillers and sealants Part 2: Specifications for cold applied sealants; EN 14188-3, Joint fillers and sealants Part 3: Specifications for preformed joint seals; EN 14188-4, Joint fillers and sealants
8、Part 4: Specifications for primers to be used with joint sealants. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, F
9、inland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 14188-4:2009 (E) 4 1 Scope This European Standard specifies requirements
10、for material characterisation for primers for hot and cold applied joint sealants for use in roads, airfields and other concrete pavements. This European Standard also applies to primers for hot and cold applied joint sealants in bituminous surfacing and a bituminous surfacing and an adjacent concre
11、te pavement. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1
12、427, Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method EN 12697-3, Bituminous mixtures - Test methods for hot mix asphalt - Part 3: Bitumen recovery: Rotary evaporator EN 14188-1:2004, Joint fillers and sealants Part 1: Specifications for hot applied sealan
13、ts EN 14188-2:2004, Joint fillers and sealants Part 2: Specifications for cold applied sealants EN 15466-1, Primers for cold and hot applied joint sealants Part 1: Determination of homogeneity EN 15466-2, Primers for cold and hot applied joint sealants Part 2: Determination of resistance against alk
14、ali EN 15466-3, Primers for cold and hot applied joint sealants Part 3: Determination of solids content and evaporation behaviour of volatiles EN 26927:1990, Building construction Jointing products Sealants Vocabulary (ISO 6927:1981) EN ISO 2431, Paints and varnishes Determination of flow time by us
15、e of flow cups (ISO 2431:1993, including Technical Corrigendum 1:1994) EN ISO 2719, Determination of flash point Pensky-Martens closed cup method (ISO 2719:2002) EN ISO 2811-2, Paints and varnishes - Determination of density - Part 2: Immersed body (plummet) method (ISO 2811-2:1997) EN ISO 9001, Qua
16、lity management systems Requirements (ISO 9001:2008) 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 14188-1:2004, EN 14188- 2:2004 and EN 26927:1990 and the following apply. 3.1 manufacturers limiting value MLV manufacturers stated minimum o
17、r maximum value to be met during testing according to the requirements of this European Standard EN 14188-4:2009 (E) 5 3.2 manufacturers declared value MDV value declared by the manufacturer accompanied by a declared tolerance 4 Types Primers for joint sealants shall be one of the types given in Tab
18、le 1. Table 1 Types of primers for joint sealants Primer Type Bitumen based for hot applied joint sealants PBH Resin based for hot applied joint sealants PRH Resin based for cold applied joint sealants (One component primer) PRC-o Resin based for cold applied joint sealants (Multi-component primer)
19、PRC-m 5 Requirements 5.1 Homogeneity The homogeneity after homogenization shall be determined in accordance with EN 15466-1 and shall give a result “homogenous“. 5.2 Density The density shall be determined in accordance with EN ISO 2811-2 and the results shall lie within the declared tolerance of th
20、e MDV. The tolerance of the MDV shall lie within 5 % and +5 %. 5.3 Viscosity The viscosity shall be determined in accordance with EN ISO 2431 and the results shall lie within the declared tolerance of the MDV. The tolerance of the MDV shall lie within 15 % and +15 %. 5.4 Resistance against alkali Th
21、e resistance against alkali shall be determined in accordance with EN 15466-2 and shall give a result “resistant“. 5.5 Evaporation behaviour of volatiles The evaporation behaviour of volatiles shall be determined in accordance with EN 15466-3 and the results shall lie within the declared tolerance o
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 14188-4-2009 嵌缝胶和密封剂.与接缝密封胶一起使用的涂底剂规范 14188 2009 嵌缝胶 密封剂 接缝 密封胶 一起 使用 涂底剂 规范
链接地址:https://www.31doc.com/p-3646635.html