BS EN 61310-2-2008 机械安全.指示、标记和传动作用.标记要求1.pdf
《BS EN 61310-2-2008 机械安全.指示、标记和传动作用.标记要求1.pdf》由会员分享,可在线阅读,更多相关《BS EN 61310-2-2008 机械安全.指示、标记和传动作用.标记要求1.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 61310-2:2008 Safety of machinery Indication, marking and actuation Part 2: Requirements for marking ICS 13.110; 29.020 BS EN 61310-2:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2009 BSI 2009 ISBN 97
2、8 0 580 54538 2 National foreword This British Standard is the UK implementation of EN 61310-2:2008. It is identical to IEC 61310-2:2007. It supersedes BS EN 61310-2:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee , Safety of machinery Electrotec
3、hnical aspects.MCE/3 A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard canno
4、t confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments W 7 7 - - $ - - - w - - - - - - - - 77 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EN 61310-2:2008 2 CONTE
5、NTS 1 Scope. 2Normative references . 3Terms and definitions . 4Marking for identification and for safe use . 4.1General . 4.2Marking of complete machinery. 4.3Marking for safe use. 5Application of markings 5.1General . 5.2Representation of rated values. 6Marking of connections. 6.1General . 6.2Mecha
6、nical connections 9 6.3Connections for fluid systems.9 6.4Electrical connections.9 7Durability of markings and their attachment .9 Annex A (informative) Graphical symbols and safety signs Bibliography 3 Annex A (normative) - - - - . Annex (informative) - - - . Annex A (informative) - - . Annex A (in
7、formative) - - EN 61310-2:2008 - This part of IEC 61310 specifies requirements for the marking of machinery. It gives general rules on marking for identification of machinery, for safe use related to mechanical and electrical hazards, and for the avoidance of hazards arising from incorrect connectio
8、ns. - The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60027-1:1992, Letter symbols to be used
9、 in electrical technology Part 1: General IEC 60027-2:2005, Letter symbols to be used in electrical technology Part 2: Telecommunications and electronics IEC 60027-3:2002, Letter symbols to be used in electrical technology Part 3: Logarithmic and related quantities, and their units IEC 60027-4:1985,
10、 Letter symbols to be used in electrical technology Part 4: Symbols for quantities to be used for rotating electrical machines IEC 60079-0:2004, Electrical apparatus for explosive gas atmospheres Part 0: General requirements IEC 60204-1:2005, Safety of machinery Electrical equipment of machines Part
11、 1: General requirements IEC 60417-DB, Graphical symbols for use on equipment IEC 60529:1989, Degrees of protection provided by enclosures (IP Code) Amendment 1 (1999) IEC 61310-1, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, acoustic and tactile signals ISO
12、 31-0:1992, Quantities and units Part 0: General principles ISO 1000:1992, SI units and recommendations for the use of their multiples and of certain other units 4 EN 61310-2:2008 ISO 7000:2004, Graphical symbols for use on equipment Index and synopsis ISO 7010:2003, Graphical symbols Safety colours
13、 and safety signs Safety signs used in workplaces and public areas ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology ISO 12100-2:2003, Safety of machinery Basic concept, general principles for design Part 2: Technical principle
14、s - - For the purposes of this document, the following terms and definitions, in addition to those of IEC 61310-1, apply. value of a quantity used for specification purposes, established for a specified set of operating conditions of a component, device, equipment, or system IEV 151-16-08 set of rat
15、ed values and operating conditions of a component, device, equipment or machine IEV 151-16-11, modified application of labelling on a product or on a package primarily for the purpose of identifying the product, and certain features of the product, for its safe use - - In accordance with ISO 12100-2
16、, machinery shall bear all markings which are necessary for its unambiguous identification; for its safe use; and supplementary information shall be given, as appropriate: permanently on the machinery; in accompanying documents such as instruction handbooks; on the packaging. 5 EN 61310-2:2008 The f
17、ollowing information shall be provided: identification of the product including name and address of the supplier, designation of series or type, serial number, if any, and year of construction; designation of rated values; indication of compliance with mandatory requirements if any. - - Where essent
18、ial for safe use, the relevant rated values and characteristics listed in 4.3.2, 4.3.3 and 4.3.4 shall be given. - - These may include, but not be limited to: a) power input/output; b) maximum speed of rotating parts; c) mass (of removable parts, etc.); d) maximum diameter of tools to be fitted; e)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 61310-2-2008 机械安全.指示、标记和传动作用.标记要求1 61310 2008 机械 安全 指示 标记 传动 作用 要求
链接地址:https://www.31doc.com/p-3647882.html