BS EN 61784-5-10-2008 工业通讯网络.剖面图.现场总线的安装.CPF 10用安装剖面图.pdf
《BS EN 61784-5-10-2008 工业通讯网络.剖面图.现场总线的安装.CPF 10用安装剖面图.pdf》由会员分享,可在线阅读,更多相关《BS EN 61784-5-10-2008 工业通讯网络.剖面图.现场总线的安装.CPF 10用安装剖面图.pdf(22页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 61784-5-10:2008 Industrial communication networks Profiles Part 5-10: Installation of fieldbuses Installation profiles for CPF 10 ICS 25.040.40; 35.100.05 BS EN 61784-5-10:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committ
2、ee on 29 August 2008 BSI 2008 ISBN 978 0 580 61656 3 National foreword This British Standard is the UK implementation of EN 61784-5-10:2008. It is identical to IEC 61784-5-10:2007. The UK participation in its preparation was entrusted to Technical Committee AMT/7, Industrial communications: process
3、measurement and control, including fieldbus. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with
4、a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments EUROPEAN STANDARD EN 61784-5-10 NORME EUROPENNE EUROPISCHE NORM June 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Elect
5、rotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61784-5-10:2008 E ICS 35.100.05; 25.040.40 English versio
6、n Industrial communication networks - Profiles - Part 5-10: Installation of fieldbuses - Installation profiles for CPF 10 (IEC 61784-5-10:2007) Rseaux de communication industriels - Profils - Partie 5-10: Installation des bus de terrain - Profils dinstallation pour CPF 10 (CEI 61784-5-10:2007) Indus
7、trielle Kommunikationsnetze - Profile - Teil 5-10: Feldbusinstallation - Installationsprofile fr die Kommunikationsprofilfamilie 10 (IEC 61784-5-10:2007) This European Standard was approved by CENELEC on 2008-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
8、stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European St
9、andard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the nat
10、ional electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed
11、en, Switzerland and the United Kingdom. Foreword The text of document 65C/471/FDIS, future edition 1 of IEC 61784-5-10, prepared by SC 65C, Industrial networks, of IEC TC 65, Industrial-process measurement, control and automation, was submitted to the IEC-CENELEC parallel vote and was approved by CE
12、NELEC as EN 61784-5-10 on 2008-05-01. This standard is to be used in conjunction with EN 61918:2008. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-02-01 latest date by
13、which the national standards conflicting with the EN have to be withdrawn (dow) 2011-05-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61784-5-10:2007 was approved by CENELEC as a European Standard without any modification. _ BS EN 61784-5-10:2
14、008 2 CONTENTS INTRODUCTION. 1 Scope. 2 Normative references . 3 Terms, definitions and abbreviated terms . 4 CPF 10: Overview of installation profiles 5 Installation profile conventions . 6 Conformance to installation profiles Annex A (normative) CP 10/1 (Vnet/IP) specific installation profile . A.
15、1 Installation profile scope A.2 Normative references A.3 Installation profile terms, definitions, and abbreviated terms A.3.1 Terms and definitions A.3.2 Abbreviated terms . A.3.3 Conventions for installation profiles . A.4 Installation planning A.4.1 Introduction . A.4.2 Planning requirements. A.4
16、.3 Network capabilities A.4.4 Selection and use of cabling components 1 A.4.5 Cabling planning documentation1 A.4.6 Verification of cabling planning specification1 A.5 Installation implementation1 A.5.1 General requirements1 A.5.2 Cable installation.1 A.5.3 Connector installation1 A.5.4 Terminator i
17、nstallation.1 A.5.5 Device installation .1 A.5.6 Coding and labeling.1 A.5.7 Earthing and bonding of equipment and devices and shield cabling.1 A.5.8 As-implemented cabling documentation.1 A.6 Installation verification and installation acceptance test.1 A.6.1 Introduction .1 A.6.2 installation verif
18、ication.1 A.6.3 Installation acceptance test .1 A.6.3.4 Specific requirements for wireless installation1 A.7 Installation administration1 A.8 Installation maintenance and installation troubleshooting 1 Bibliography1 Figure 1 Standards relationships Table A.1 Network characteristics for balanced cabl
19、ing based on Ethernet 1 Table A.2 Network characteristics for optical fibre cabling1 - - - - BS EN 61784-5-10:2008 3 Table A.4 Information relevant to copper cable: cords1 Table A.5 Information relevant to optical fibre cables.1 Table A.6 Connectors for balanced cabling CPs based on Ethernet .1 Tabl
20、e A.7 Optical fibre connecting hardware1 Table A.3 Information relevant to copper cable: fixed cables1 BS EN 61784-5-10:2008 4 INTRODUCTION This International Standard is one of a series produced to facilitate the use of communication networks in industrial control systems. IEC 61918:2007 (Ed. 1.0)
21、provides the common requirements for the installation of communication networks in industrial control systems. This installation profile standard provides the installation profiles of the communication profiles (CP) of a specific communication profile family (CPF) by stating which requirements of IE
22、C 61918 fully apply and, where necessary, by supplementing, modifying, or replacing the other requirements (see Figure 1). For general background on fieldbuses, their profiles, and relationship between the installation profiles specified in this standard, see IEC/TR 61158-1. Each CP installation pro
23、file is specified in a separate annex of this standard. Each annex is structured exactly as the reference standard IEC 61918 for the benefit of the persons representing the roles in the fieldbus installation process as defined in IEC 61918 (planner, installer, verification personnel, validation pers
24、onnel, maintenance personnel, administration personnel). By reading the installation profile in conjunction with IEC 61918, these persons immediately know which requirements are common for the installation of all CPs and which are modified or replaced. The conventions used to draft this standard are
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 61784-5-10-2008 工业通讯网络.剖面图.现场总线的安装.CPF 10用安装剖面图 61784 10 2008 工业 通讯 网络 剖面图 现场总线 安装 CPF
链接地址:https://www.31doc.com/p-3647970.html