BS EN 626-2-1996 Safety of machinery — Reduction of risk to health from hazardous substances emitted by machinery.pdf
《BS EN 626-2-1996 Safety of machinery — Reduction of risk to health from hazardous substances emitted by machinery.pdf》由会员分享,可在线阅读,更多相关《BS EN 626-2-1996 Safety of machinery — Reduction of risk to health from hazardous substances emitted by machinery.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 626-2:1996 Safety of machinery Reduction of risk to health from hazardous substances emitted by machinery Part 2: Methodology leading to verification procedures The European Standard EN 626-2:1996 has the status of a British Standard ICS 13.110 BS EN 626-2:1996 This British St
2、andard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 December 1996 BSI 10-1998 The following BSI references relate to the work on this standard: Committee reference MCE/3 Draft for comme
3、nt 94/704395 DC ISBN 0 580 26470 X Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee MCE/3, Safeguarding of machinery, upon which the following bodies were represented: Advanced Manufacturing Technology Research Institute B
4、ritish Cable Makers Confederation British Compressed Air Society British Robot Association British Rubber Manufacturers Association British Textile Machinery Association Consumer Policy Committee of BSI Health and Safety Executive Loss Prevention Council Machine Tool Technologies Association Machine
5、ry Safety Equipment Manufacturers Association PICON Society of Laundry Engineers and Allied Trades Limited Trades Union Congress Amendments issued since publication Amd. No.DateComments BS EN 626-2:1996 BSI 10-1998i Contents Page Committees responsibleInside front cover National forewordii Foreword2
6、 Text of EN 626-23 BS EN 626-2:1996 ii BSI 10-1998 National Foreword This British Standard has been prepared under the direction of the Engineering Sector Board and is the English language version of EN 626-2Safety of machinery Reduction of risks to health from hazardous substances emitted by machin
7、ery Part 2: Methodology leading to verification procedures, published by the European Committee for Standardization (CEN). EN 626-2 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of
8、 a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred toCorresponding British Standard EN 292-1:1991BS EN 292 Safety of machinery Basic
9、 concepts, general principles for design Part 1:1991 Basic terminology, methodology EN 626-1:1994BS EN 626 Safety of machinery Reduction of risks to health from hazardous substances emitted by machinery Part 1:1995 Principles and specification for machinery manufacturers Summary of pages This docume
10、nt comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. ? EUROPEAN STAN
11、DARD NORME EUROPENNE EUROPISCHE NORM EN 626-2 July 1996 ICS 00.; 13.110 Descriptors: Safety of machine, work safety, air pollution, emission, dust, dangerous materials, hazards, safety measures, design, verification, inspection methods, maintenance English version Safety of machinery Reduction of ri
12、sk to health from hazardous substances emitted by macinery Part 2: Methodology leading to verification procedures Scurit des machines Rduction du risque pour la sant rsultant de substances dangereuses mises par les machines Partie 2: Mthodologie menant des procdures de vrification Sicherheit von Mas
13、chinen Reduzierung des Gesundheitsrisikos durch Gefahrstoffe, die von Maschinen ausgehen Teil 2: Methodik beim Aufstellen von berprfungsverfahren This European Standard was approved by CEN on 1996-06-20. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the co
14、nditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in thre
15、e official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Aus
16、tria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: r
17、ue de Stassart 36, B-1050 Brussels All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 626-2:1996 E ? EN 626-2:1996 2 BSI 10-1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 114, S
18、afety of machinery, of which the Secretariat is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1997, and conflicting national standards shall be withdrawn at the latest by Ja
19、nuary 1997. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Directive(s). According to the CEN/CENELEC Internal Regulations, the national standards organizations of
20、 the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 0Introduction3 1Scope3 2
21、Normative references3 3Methodology3 3.1Identification of hazardous substances3 3.2Characterization of emissions3 3.3Identification of critical factors4 3.4Specification of indicative parameters4 4Verification4 Annex A (normative) Flow diagram leading to verification procedures5 Annex B (informative)
22、 Examples of types of emission and how to assess them5 Annex C (informative) Examples of relevant factors and their indicative parameters6 ? EN 626-2:1996 BSI 10-19983 0 Introduction This European Standard is one of a group of standards produced by CEN/CENELEC under mandates from CEC and EFTA. This
23、group has been divided into several categories to avoid duplication and to develop a logical structure which will enable rapid production of standards and easy cross reference between them. The hierarchy of standards is as follows: a) Type A standards (genetic safety standards) giving basic concepts
24、, principles for design and general aspects that can be applied to all machinery. b) Type B standards (group safety standards) dealing with one safety aspect or one type of safety related device that can be used across a wide range of machinery: type B1 standards on particular safety aspects (e.g. s
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 626-2-1996 Safety of machinery Reduction risk to health from hazardous substances emitted by 626
链接地址:https://www.31doc.com/p-3648058.html