BS EN 693-2001+A1-2009 机床的安全性.液压机.pdf
《BS EN 693-2001+A1-2009 机床的安全性.液压机.pdf》由会员分享,可在线阅读,更多相关《BS EN 693-2001+A1-2009 机床的安全性.液压机.pdf(58页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 693:2001 Machine tools Safety Hydraulic presses ICS 25.120.10 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 BSI 2009 Amen
2、dments issued since publication DateComments National foreword This British Standard is the UK Implementation of EN 693:2001+A1:2009. It supersedes BS EN 693:2001 which is withdrawn. The UK is obliged to publish EN 693:2001 as a British Standard (BS EN 693:2001). However, attention is drawn to the f
3、act that during the development of this European Standard the United Kingdom has consistently voted against its approval as an EN. The UK with the state of the art for these machines in the UK. The standard fails As part of BSIs duty of care we draw attention to users of BS EN 693:2001 of of personn
4、el against access to the danger zone at manually loaded/unloaded device(s) is concerned. When these devices are provided as the sole safeguard liability whatsoever for any failure on the part of any user of this standard to consider these aspects. indicated by . The UK participation in its preparati
5、on was entrusted by Technical machine tools. A list of organizations represented on this subcommittee can be obtained on This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cann
6、ot confer immunity from legal obligations. Implementation of CEN amendment A1:200931 May 2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 693:2001+A1 February 2009 ICS 25.120.10 Supersedes EN 693:2001 English Version Machine tools - Safety - Hydraulic presses Machines-outils - Scurit - Pres
7、ses hydrauliques Werkzeugmaschinen - Sicherheit - Hydraulische Pressen This European Standard was approved by CEN on 20 November 2000 and includes Amendment 1 approved by CEN on 29 December 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
8、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three off
9、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austri
10、a, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMIT
11、TEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 693:2001+A1:2009: E EN 693:2001+A1:2009
12、 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 4 2 Normative references 5 3 Terms and definitions .6 4 List of hazards . 12 5 Safety requirements and measures 14 5.1 Introduction . 14 5.2 Basic design considerations . 14 5.3 Mechanical hazards in the tools area . 17 5.4 The control and moni
13、toring system 21 5.5 Toolsetting, trial strokes, maintenance and lubrication . 24 5.6 Mechanical hazards - Other . 25 5.7 Slips, trips and falls 26 5.8 Protection against other hazards 26 6 Verification of the safety requirements and/or measures 33 7 Information for use . 39 7.1 Marking 39 7.2 Instr
14、uction handbook . 40 Annex A (normative) Calculation of minimum safety distances . 42 Annex B (normative) The response time of the hydraulic system 44 Annex C (informative) Closed tools 45 Annex D (informative) Interlocking devices associated with guards . 46 Annex E (informative) Electro-sensitive
15、protective equipment (ESPE) using active opto-electronic protective devices (AOPDs) . 49 Annex F (informative) Conditions for noise measurement of hydraulic presses 50 Annex G (informative) The connection of the stopping time measurement equipment . 52 Annex ZA (informative) !Relationship between th
16、is European Standard and the Essential Requirements of EU Directive 98/37/EC amended by Directive 98/79/EC“ . 53 Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 54 Bibliography . 55 BS EN 693:2001+A1:2009 EN 693:2001+A1:2
17、009 (E) 3 Foreword This document (EN 693:2001+A1:2009) has been prepared by Technical Committee CEN/TC 143 “Machine tools - Safety”, the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo
18、rsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-12-29. This document supersedes EN 693:2001. The start and finish of text introduced or altered by amendment is ind
19、icated in the text by tags ! “. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB,
20、 which are integral parts of this document.“ Annexes A and B to this standard are normative, whereas Annexes C to G!, ZA and ZB“ are informative. This standard also contains a bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following count
21、ries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai
22、n, Sweden, Switzerland and United Kingdom. BS EN 693:2001+A1:2009 EN 693:2001+A1:2009 (E) 4 Introduction 0.1 This standard is applicable to hydraulic presses as defined in 3.10. 0.2 This standard has been prepared to be a harmonized standard to provide one means of conforming with the essential safe
23、ty requirements of the “Machinery“ Directive and associated EFTA Regulations. 0.3 The extent to which hazards are covered is indicated in the scope of this standard. In addition, machinery shall comply as appropriate with EN 292 for hazards which are not covered by this standard. 0.4 Complementary g
24、uidance is given in the A and B standards to which reference is made in the text (see clause 2). The figures are intended to be examples only and not to give the only interpretation of the text. 1 Scope 1.1 This standard specifies technical safety requirements and measures to be adopted by persons u
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 693-2001+A1-2009 机床的安全性.液压机 693 2001 A1 2009 机床 安全性 液压机
链接地址:https://www.31doc.com/p-3648065.html