BS EN 729-1-1995 Quality requirements for welding Fusion welding of metallic materials — Part 1 Guidelines for selection and use.pdf
《BS EN 729-1-1995 Quality requirements for welding Fusion welding of metallic materials — Part 1 Guidelines for selection and use.pdf》由会员分享,可在线阅读,更多相关《BS EN 729-1-1995 Quality requirements for welding Fusion welding of metallic materials — Part 1 Guidelines for selection and use.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 729-1:1995 Incorporating Amendment No. 1 Quality requirements for welding Fusion welding of metallic materials Part 1: Guidelines for selection and use The European Standard EN 729-1:1994 has the status of a British Standard UDC 621.792:658.562 Copyright British Standards Inst
2、itution Reproduced by IHS under license with BSI - Uncontrolled Copy Document provided by IHS Licensee=Bureau Veritas/5959906001, 11/08/2004 05:30:03 MST Questions or comments about this message: please call the Document Policy Group at 303-397-2295. -,-,- BS EN 729-1:1995 This British Standard, hav
3、ing been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1995 BSI 12-1998 The following BSI references relate to the work on this standard: Committee reference WEE/-/1/6 Draft for comment 92/75
4、856 DC ISBN 0 580 23131 3 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: AustriaOesterreichisches Normungsinstitut BelgiumInstitut belg
5、e de normalisation DenmarkDansk Standard FinlandSuomen Standardisoimisliito, r.y. FranceAssociation franaise de normalisation GermanyDeutsches Institut fr Normung e.V. GreeceHellenic Organization for Standardization IcelandTechnological Institute of Iceland IrelandNational Standards Authority of Ire
6、land ItalyEnte Nazionale Italiano di Unificazione LuxembourgInspection du Travail et des Mines NetherlandsNederlands Normalisatie-instituut NorwayNorges Standardiseringsforbund PortugalInstituto Portugus da Qualidade SpainAsociacin Espaola de Normalizacin y Certificacin SwedenStandardiseringskommiss
7、ionen i Sverige SwitzerlandAssociation suisse de normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.DateComments 8849December 1995 Indicated by a sideline in the margin Copyright British Standards Institution Reproduced by IHS under license with BSI
8、 - Uncontrolled Copy Document provided by IHS Licensee=Bureau Veritas/5959906001, 11/08/2004 05:30:03 MST Questions or comments about this message: please call the Document Policy Group at 303-397-2295. -,-,- BS EN 729-1:1995 BSI 12-1998i Contents Page Cooperating organizationsInside front cover Nat
9、ional forewordii Foreword2 Text of EN 729-13 National annex NA (informative) Committees responsibleInside back cover National annex NB (informative) Cross-referencesInside back cover Copyright British Standards Institution Reproduced by IHS under license with BSI - Uncontrolled Copy Document provide
10、d by IHS Licensee=Bureau Veritas/5959906001, 11/08/2004 05:30:03 MST Questions or comments about this message: please call the Document Policy Group at 303-397-2295. -,-,- BS EN 729-1:1995 ii BSI 12-1998 National foreword This British Standard has been prepared under the direction of the Engineering
11、 Sector Board and is the English language version of EN 729-1:1994 Quality requirements for welding Fusion welding of metallic materials Part 1: Guidelines for selection and use, published by the European Committee for Standardization (CEN). EN 729-1 was produced as the result of international discu
12、ssion in which the UK took and active part. There has previously been no direct British Standard equivalent to this standard. Application Standards may request the manufacturer to comply with one of the Parts of EN 729. It is assumed that the execution of the provisions of this document is entrusted
13、 to suitably qualified and experienced persons. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obliga
14、tions. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the am
15、endment table on the inside front cover. Copyright British Standards Institution Reproduced by IHS under license with BSI - Uncontrolled Copy Document provided by IHS Licensee=Bureau Veritas/5959906001, 11/08/2004 05:30:03 MST Questions or comments about this message: please call the Document Policy
16、 Group at 303-397-2295. -,-,- ? EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 729-1 September 1994 UDC 621.792:658.562 Descriptors: Welding, welded constructions, quality, quality assurance, selection, utilization; manufacturing, user supplier relations English version Quality requirements fo
17、r welding Fusion welding of metallic materials Part 1: Guidelines for selection and use Exigences de qualit en soudage Soudage par fusion des matriaux mtalliques Partie 1: Lignes directrices pour la slection et l utilisation Schweitechnische Qualititsanforderungen Schmelzschweien metallischer Werkst
18、offe Teil 1: Richtlinien zur Auswahl und Verwendung This European Standard was approved by CEN on 1994-09-06. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter
19、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by transl
20、ation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg
21、, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN 729-1:1
22、994 E Copyright British Standards Institution Reproduced by IHS under license with BSI - Uncontrolled Copy Document provided by IHS Licensee=Bureau Veritas/5959906001, 11/08/2004 05:30:03 MST Questions or comments about this message: please call the Document Policy Group at 303-397-2295. -,-,- ? EN
23、729-1:1994 BSI 12-1998 2 Foreword This European Standard was prepared by the Technical Committee CEN/TC 121, Welding, of which the secretariat is held by DS. CEN/TC 121 has decided to submit the final draft for formal vote by its resolution 173/1993. The result was positive. EN 729 is composed of th
24、e four following parts: EN 729-1, Quality requirements for welding Fusion welding of metallic materials Part 1: Guidelines for selection and use; EN 729-2, Quality requirements for welding Fusion welding of metallic materials Part 2: Comprehensive quality requirements; EN 729-3, Quality requirements
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 729-1-1995 Quality requirements for welding Fusion of metallic materials Part Guidelines selection 729
链接地址:https://www.31doc.com/p-3648132.html