BS EN 764-5-2002 PRESSURE EQUIPMENT — PART 5 COMPLIANCE AND INSPECTION DOCUMENTATION OF MATERIALS.pdf
《BS EN 764-5-2002 PRESSURE EQUIPMENT — PART 5 COMPLIANCE AND INSPECTION DOCUMENTATION OF MATERIALS.pdf》由会员分享,可在线阅读,更多相关《BS EN 764-5-2002 PRESSURE EQUIPMENT — PART 5 COMPLIANCE AND INSPECTION DOCUMENTATION OF MATERIALS.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 764-5:2002 Pressure Equipment Part 5: Compliance and Inspection Documentation of Materials The European Standard EN 764-5:2002 has the status of a British Standard ICS 23.020.30 ? - - - BS EN 764-5:2002 This British Standard, having been prepared under the direction of the Eng
2、ineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 4 December 2002 BSI 4 December 2002 ISBN 0 580 40894 9 National foreword This British Standard is the official English language version of EN 764-5:2002. When the refere
3、nce to this European Standard has been published in the Official Journal of the European Communities (OJ), compliance with it will confer a presumption of conformity with the essential requirements covered by this standard in respect of the Pressure Equipment Directive (97/23/EC). The UK participati
4、on in its preparation was entrusted by Technical Committee PVE/1, Pressure vessels, to Subcommittee PVE/1/14, Materials selection, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Stand
5、ards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This
6、 publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible inter
7、national/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN t
8、itle page, pages 2 to 13 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 764-5 October 2002 ICS 23.020.30 English version Pr
9、essure Equipment - Part 5: Compliance and Inspection Documentation of Materials Equipements sous pression - Partie 5: Documents de conformit et de contrle des matriaux Druckgerte - Teil 5: Prfbescheinigungen fr metallische Werkstoffe und bereinstimmung mit der Werkstoffspezif kation This European St
10、andard was approved by CEN on 19 August 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin
11、g such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own langua
12、ge and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Swede
13、n, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
14、Ref. No. EN 764-5:2002 E EN 764-5:2002 (E) 2 Contents page Foreword3 1Scope 4 2Normative references 4 3Requirements with respect to pressure equipment categories4 3.1General4 3.2Material for main pressure bearing parts in category II, III and IV.5 3.3Material for pressure parts not covered by 3.2 an
15、d for attachments in category II, III and IV 5 3.4Other material.5 3.5Welding consumables.5 3.6Use of higher document levels.5 4Material manufacturers quality system route.5 4.1General5 4.2Quality system5 4.3Material testing and inspection documents6 5Direct inspection route7 5.1First production7 5.
16、2Inspectors.7 5.3Material testing and inspection documents7 6Material from stockists8 6.1Inspection documents and marking 8 6.2Cut off material pieces 8 7Specific requirements for material containing welds - components8 7.1General8 7.2Welding procedures and welders qualification8 7.3Non-destructive
17、testing of permanent joints9 Annex A (normative) Approval and appraisal procedures for materials10 A.1General10 A.2Competent body.10 A.3Experienced and competent body .10 A.4Accredited body.10 A.5Competent third party inspection body.10 A.6Conformity assessment of pressure equipment materials.10 Ann
18、ex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives12 Bibliography13 - - - EN 764-5:2002 (E) 3 Foreword This document EN 764-5:2002 has been prepared by Technical Committee CEN/TC 54 “Unfired pressure vessels“, the secretariat
19、of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2003, and conflicting national standards shall be withdrawn at the latest by April 2003. This document has been prepa
20、red under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Directive 97/23/EC. For relationship with the EU Directive, see informative annex ZA which is an integral part of this document. This European Standard “
21、Pressure equipment” consists of seven Parts which are: Part 1: Pressure, temperature, volume, nominal size. Part 2: Quantities, symbols and units. Part 3: Definition of parties involved. Part 4: Establishment of technical delivery conditions for materials. Part 5: Compliance and Inspection Documenta
22、tion of Materials; Part 6: Operating instructions. Part 7: Safety systems and unfired pressure equipment. Annex A is normative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun- tries are bound to implement this European Standard: Austria,
23、 Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Swe- den, Switzerland and the United Kingdom. EN 764-5:2002 (E) 4 1 Scope This Part of this European Standard specifies the materials for pressure eq
24、uipment to comply with the requirements of the relevant pressure equipment material specification. This Part describes how this shall be applied to materials intended for the manufacturing of pressure bearing parts and attachments to them. A simplified diagram of the routes for inspection documentat
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 764-5-2002 PRESSURE EQUIPMENT PART COMPLIANCE AND INSPECTION DOCUMENTATION OF MATERIALS 764 2002
链接地址:https://www.31doc.com/p-3648197.html