IEEE Std 1115-2000 IEEE Recommended Practice for Sizing Nickel-Cadmium Batteries for Stationary Applications.pdf
《IEEE Std 1115-2000 IEEE Recommended Practice for Sizing Nickel-Cadmium Batteries for Stationary Applications.pdf》由会员分享,可在线阅读,更多相关《IEEE Std 1115-2000 IEEE Recommended Practice for Sizing Nickel-Cadmium Batteries for Stationary Applications.pdf(26页珍藏版)》请在三一文库上搜索。
1、 The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2000 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 11 September 2000. Printed in the United States of America. Print: ISBN 0-7381-1950-4
2、SH94818 PDF: ISBN 0-7381-1951-2 SS94818 No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. IEEE Std 1115-2000 (Revision of IEEE Std 1115-1992) IEEE Recommended Practice for Sizing Nickel-Ca
3、dmium Batteries for Stationary Applications Sponsor IEEE Standards Coordinating Committee 29 on Stationary Batteries Approved 30 March 2000 IEEE-SA Standards Board Abstract: The sizing of nickel-cadmium batteries used in full fl oat operation for stationary applications is covered in this recommende
4、d practice. Keywords: nickel-cadmium batteries, stationary applications IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating Com- mittees of the IEEE Standards Association (IEEE-SA) Standards Board. Members of the committees serve voluntarily and without co
5、mpensation. They are not necessarily members of the Institute. The standards developed within IEEE represent a consensus of the broad expertise on the subject within the Institute as well as those activities outside of IEEE that have expressed an interest in participating in the development of the s
6、tandard. Use of an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at the
7、time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. Every IEEE Standard is subjected to review at least every fi ve years for revision or reaffi rmation. When a document is more than
8、fi ve years old and has not been reaffi rmed, it is rea- sonable to conclude that its contents, although still of some value, do not wholly refl ect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE Standard. Comments for revision o
9、f IEEE Standards are welcome from any interested party, regardless of membership affi liation with IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Interpretations: Occasionally questions may arise regarding
10、 the meaning of portions of standards as they relate to specifi c applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiate action to prepare appropriate responses. Since IEEE Standards represent a consensus of all concerned interests, it is imp
11、ortant to ensure that any interpretation has also received the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to interpretation requests except in those cases where the ma
12、tter has previously received formal consideration. Comments on standards and requests for interpretations should be addressed to: Secretary, IEEE-SA Standards Board 445 Hoes Lane P.O. Box 1331 Piscataway, NJ 08855-1331 USA IEEE is the sole entity that may authorize the use of certifi cation marks, t
13、rademarks, or other designations to indicate compliance with the materials set forth herein. Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is pai
14、d to Copyright Clearance Center. To arrange for payment of licensing fee, please contact Copyright Clearance Center, Cus- tomer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; (978) 750-8400. Permission to photocopy portions of any individual standard for educational classroom use can also be ob
15、tained through the Copy- right Clearance Center. Note: Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent
16、 rights in connection therewith. The IEEE shall not be responsible for identifying patents for which a license may be required by an IEEE standard or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. Copyright 2000 IEEE. All rights reserved
17、. iii Introduction (This introduction is not part of IEEE 1115-2000, IEEE Recommended Practice for Sizing Nickel-Cadmium Batteries for Stationary Applications.) The storage battery is of primary importance in ensuring the satisfactory operation of generating stations, substations, and other stationa
18、ry applications. This recommended practice is based on commonly accepted methods used to defi ne the load and to ensure adequate battery capacity. The method described is applicable to all installations and battery sizes. The installations considered herein are designed for operation with a battery
19、charger serving to maintain the battery in a charged condition as well as to supply the normal dc load. Alternate energy systems (e.g., wind- mills and photovoltaic systems) may provide only partial or intermittent charging, and are beyond the scope of this document. See IEEE Std 1144-1996 B6 1 for
20、details. This recommended practice was prepared by the Nickel-Cadmium Sizing Working Group of IEEE Standards Coordinating Committee 29 (SCC29). It may be used separately, but when combined with IEEE Std 1106-1995, it will provide the user with a general guide to designing, placing in service, and ma
21、intaining a nickel-cadmium battery installation. At the time this standard was approved the members of the Nickel- Cadmium Sizing Working Group were as follows: James A. McDowall, Chair The following persons were on the balloting committee: When the IEEE-SA Standards Board approved this standard on
22、30 March 2000, it had the following membership: Donald N. Heirman, Chair James T. Carlo, Vice Chair Judith Gorman, Secretary *Member Emeritus 1 The numbers in brackets correspond to those of the bibliography in Annex D. Richard T. Bolgeo Jay L. Chamberlin Anthony Green Jos Marrero Leif Olsson Lesley
23、 Varga Graham Walker Curtis Ashton Terry Bostian Jay L. Chamberlin John K. Coyle Thomas G. Croda Peter J. DeMar Harold E. Epstein Timothy Furlong Richard A. Greco Paul E. Hellen Robert M. Herritty Daniel S. Levin Joel A. Long Jos A. Marrero James A. McDowall Bansi Patel Robert S. Robinson Saba N. Sa
24、ba Martin M. Stanton Frank L. Tarantino Kurt W. Uhlir Lesley Varga Satish K. Aggarwal Mark D. Bowman Gary R. Engmann Harold E. Epstein H. Landis Floyd Jay Forster* Howard M. Frazier Ruben D. Garzon James H. Gurney Richard J. Holleman Lowell G. Johnson Robert J. Kennelly Joseph L. Koepfi nger* Peter
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEE Std 1115-2000 Recommended Practice for Sizing Nickel-Cadmium Batteries Stationary Applications 1115
链接地址:https://www.31doc.com/p-3659887.html