JIS G3459-2004 英文版 不锈钢钢管.pdf
《JIS G3459-2004 英文版 不锈钢钢管.pdf》由会员分享,可在线阅读,更多相关《JIS G3459-2004 英文版 不锈钢钢管.pdf(42页珍藏版)》请在三一文库上搜索。
1、JAPANESE INDUSTRIAL STANDARD JIS G 3459 : 2004 Stainless steel pipes August, 2004 ERRATA Page 4 Table 2, the value of Si for SUS321 HTP. Error: 0.75 min Correct: 0.75 max Page 7 Informative Table 1, title. Error : 3mm in wall thickness Correct : 8mm in wall thickness Page 12 Remarks 2 of Table 5 Err
2、or: Correct: Rule B of JIS Z 8401 Rule A of JIS Z 8401 Remarks: This erratum is for correcting the first edition of this Standard. Japanese Standards Association 免费标准下载网( w w w . f r e e b z . n e t ) 免费标准下载网( w w w . f r e e b z . n e t ) 无需注册, 即可下载 J IS JAPANESE I N D U STR I AL STANDARD Translate
3、d and Published by Japanese Standards Association Stainless steel pipes ICs 23.040.10; 77.140.20; 77.140.75 Reference number : JIS G 3459 : 2004 (E) PROTECTED BY COPYRIGHT 23 S The Standard is downloaded from Standard Sharing 免费标准下载网( w w w . f r e e b z . n e t ) 免费标准下载网( w w w . f r e e b z . n e
4、 t ) 无需注册, 即可下载 G 3459 : 2004 Foreword This translation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Ind
5、ustrial Standard submitted by The Japan Iron and Steel Federation (JISF) with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14. Consequently JIS G 3459 : 1997 is replaced wi
6、th this Standard. This revision has been made based on IS0 9330-6 : 1997 Welded steel tubes for pressure purposes-Technical delivery conditions-Part 6 : Longitudinally welded austenitic stainless steel tubes and IS0 9329-4 : 1997 Seamless steel tubes for pressure purposes-Technical delivery conditio
7、ns-Part 4 : Austen- itic stainless steels for the purposes of making it easier to compare this Stan- dard with International Standards; to prepare Japanese Industrial Standard conforming with International Standards; and to propose a draft of an In- ternational Standard which is based on Japanese In
8、dustrial Standard. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical prop
9、erties. The relevant Minis- ter and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the
10、said technical properties. Date of Establishment: 1962-03-01 Date of Revision: 2004-02-20 Date of Public Notice in Official Gazette: 2004-02-20 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Iron and Steel JIS G 3459 : 2004, Second English edition pub
11、lished in 2004-08 Translated and published by: Japanese Standards Association 4-1 -24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2004 All rights reserved. Unless otherwise specified, no part o
12、f this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT 免费标准下载网( w w w . f r e e b z . n e t ) 免费标准下载网( w w w . f r e e b z
13、. n e t ) 无需注册, 即可下载 G 3459 : 2004 Contents Page Introduction . 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 Scope Normative references Classification and symbol Manufacturing method . Chemical composition . Mechanical properties . Tensile strength, proof stress and elongation Flattening or guide bend resistance
14、 weld zone . Austenitic grain size . Hydraulic test characteristic or non-destructive examination characteristic Pressure resistance performance Leaching performance . Dimensions, mass and dimensional tolerances 11.1 Dimensions and mass . 11.2 Dimensional tolerances . 12 Appearance . 13 Test 13.1 13
15、.2 13.3 13.4 13.5 13.6 Chemical analysis Tensile test . Flattening test . Guide bend test of weld zone Austenitic grain size test . Hydraulic test or non-destructive examination . 1 1 1 2 3 3 6 6 7 8 8 9 9 9 9 15 15 15 15 16 16 17 17 17 PROTECTED BY COPYRIGHT The Standard is downloaded from Standar
16、d Sharing 免费标准下载网( w w w . f r e e b z . n e t ) 免费标准下载网( w w w . f r e e b z . n e t ) 无需注册, 即可下载 G 3459 : 2004 13.7 Pressure resistance performance test 13.8 Leaching performance test . 14 Inspection 14.1 Inspection 14.2 Reinspection 15 Marking . 16 Report Annex 1 (normative) Special quality requi
17、rements . 17 18 18 18 18 18 19 23 Annex 2 (informative) Comparison table between JIS and corresponding International Standards . 27 (ii) PROTECTED BY COPYRIGHT 免费标准下载网( w w w . f r e e b z . n e t ) 免费标准下载网( w w w . f r e e b z . n e t ) 无需注册, 即可下载 JAPANESE INDUSTRIAL STANDARD JIS G 3459 : 2004 Stai
18、nless steel pipes Introduction In this revision, the addition of steel grades which have usage track records for hot water piping,. the review to make the table of dimensions and mass of welded steel pipes agree with the actual condition, the modification of the value of chemical component P to be i
19、n a conformity with 3 1 s G 4304 and JIS G 4305 and the alteration of number of specimens for the hydraulic test and non-destruc- tive examination were made. This Japanese Industrial Standard has been prepared based on each first edition of IS0 9330-6 Welded steel tubes for pressure purposes-Technic
20、al delivery condi- tions-Part 6 : Longitudinally welded austenitic stainless steel tubes and IS0 9329-4 Seamless steel tubes for pressure purposes-Technical delivery conditions-Part 4 : Austenitic stainZess steels published in 1997 with modifying some technical contents. Portions sidelined or underl
21、ined with dots are the matters modified from the original International Standards. The list of modification with its explanation is given in annex 2 (informative). 1 Scope This Standard specifies the stainless steel pipes (hereafter referred to as “pipes”) used for the piping for corrosion resistanc
22、e, low temperature service, high temperature service, etc. Remarks 1 The purchaser may designate in addition to the items specified in this text, by prior agreement with the manufacturer, part or all of the items in the special quality requirements specified in annex 1 (normative). 2 The Internation
23、al Standard corresponding to this Standard is as fol- lows. In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) ac- cording to ISOPLEC Guide 21. IS0 9330-6 : 1
24、997 IS0 9329-4 1997 Welded steel tubes for pressure purposes-Tech- nical delivery conditions-Part 6 : Longitudinally welded austenitic stainless steel tubes (MOD) Seamless steel tubes for pressure purposes-Tech- nical delivery conditions-Part 4 : Austenitic stain- less steels (MOD) 2 Normative refer
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS G3459-2004 英文版 不锈钢钢管 G3459 2004 英文 不锈钢 钢管
链接地址:https://www.31doc.com/p-3669212.html