SAE J1942-1-2002 Qualified Hoses for Marine Applications.pdf
《SAE J1942-1-2002 Qualified Hoses for Marine Applications.pdf》由会员分享,可在线阅读,更多相关《SAE J1942-1-2002 Qualified Hoses for Marine Applications.pdf(39页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2002 Society of Automotive Engineers, Inc. All rights reserved. No part of
3、this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4
4、970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS:http:/www.sae.org SURFACE VEHICLE INFORMATION REPORT J1942-1 REV. MAY2002 Issued1993-06 Revised2002-05 Superseding J1942-1 JUN1999 Qualified Hoses for Marine Applications 1.ScopeEffective August 28, 1991, the SAE replaced the
5、USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the n
6、ew test requirements listed in SAE J1942. If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion.) The following list consists of hose data provided as of May 2002, an
7、d is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25(c). Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturers recommended MAWP or type of fitting. This list has bee
8、n compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a.Successfully test their hose to the requirements of SAE J1942, Table 1. b.Submit a letter of certification to
9、the SAE J1942 test requirements for each specific type of hose tested. All sizes should be included in the same letter which must also include all of the information necessary to make a SAE J1942-1 listing. c.The SAE will review the letter and may, at their discretion, request to see some, or all, o
10、f the test results. A copy of the submittal letter marked “Accepted For Listing” will be returned to the applicant and a duplicate copy sent to the USCG. d.The cutoff date for inclusion of a hose listing in the annual SAE Handbook is April 30, of the preceding year. However, listed hoses may be used
11、 on vessels as soon as the “Accepted For Listing” letter is issued by the SAE. Next publication of this listing is scheduled to take place on December 2002. If you wish to include additional hoses in the 2002 publication of this list, please submit your Certified List to SAE Headquarters by October
12、2002. SAE J1942-1 Revised MAY2002 -2- 2.References 2.1Applicable PublicationThe following publication forms a part of the specification to the extent specified herein. Unless otherwise indicated the lastest revision of SAE publications shall apply. 2.1.1SAE PUBLICATIONAvailable from SAE, 400 Commonw
13、ealth Drive, Warrendale, PA 15096-0001 SAE J1492Hose and Hose Assemblies for Marine Applications 3.Listing Instructions(Refer to Table 1 in SAE J1942 and the attached Sample Listing Page (see Table 1). 3.1Column 1Hose NumberList each complete hose supplier catalog number, including the size (one lin
14、e listing for a series of hoses will no longer be acceptable.) 3.2Column 2Application CodeWill show an HF, F, H, VW, or NVW, nothing more! Hoses with an F and H rating, at the same working pressure, should be rated HF, good for all servies. If a hose is qualified for use in both an F and H applicati
15、on, but at different working pressures, or requires a fire sleeve for either application, it must be listed twice, once for F and once for H, with the appropriate information for each listing. Hoses listed as F can be used for VW and NVW applications and do not require a separate listing for VW and
16、NVW. Hoses listed as H can also be used for VW and NVW applications and do not require a separate listing for VW and NVW. Hoses listed as VW can also be used for NVW applications (at 50 psi). NVW listings are for NVW listings only (refer to Table 1). Because of the multiple uses for F, H, and VW hos
17、es, no hose has to be listed more than twice. 3.3Column 3Hose I.D.The actual hose I.D. shall be shown in fractions. 3.4Column 4Maximum Allowable Working PressureShall be shown in PSI. VW applications can use F and H hoses at the pressures shown in the listing or their own listed pressure. NVW applic
18、ations are all rated at 50 psi maximum. 3.5Column 5FittingsShall show the catalog number of each fitting style used on each hose size. 3.6Column 6Fire SleeveShow the number of the appropriate fire sleeve if one is required. 3.7Column 7Listing DateFor all hoses now on the USCG list, this date will be
19、 the date that SAE J1942-1 is printed. (The USCG letter date will be dropped.) Future listings will be the date the hose is added to the list by SAE. 3.8Column 8NotesWill be removed. With the individual listing of each hose size, this column will no longer be required. SAE J1942-1 Revised MAY2002 -3
20、- TABLE 1SAMPLE LISTING PAGE 1 Hose Number 2 Applic. Code 3 Hose ID 4 MAWP (PSI) 5 Fittings 6 Fire Sleeve 7 Listing Date E704H1/43000HF,EA,CH4JAN93 E705H5/162750HU,EA,CH4JAN93 E706H3/82500HU,EA,CH4JAN93 E708H1/22250HU,CH4JAN93 M716H14000HW4JAN93 M720H1-1/43000HW4JAN93 M724H1-1/42500HW4JAN93 G104HF1/
21、43000GL,EC4JAN93 G105HF5/162500GL,EC4JAN93 G106HF3/82500GL,EC4JAN93 G108HF1/22250GL,EC4JAN93 Y904H3/163000BC,BN4JAN93 Y905H1/43000BC,BN4JAN93 Y906H5/162250BC,BN4JAN93 Y910H1/21750BC,BN4JAN93 Y904F3/16300BC,BN143724JAN93 Y905F1/4300BC,BN143724JAN93 Y906F5/16300BC,BN143724JAN93 N256-2VW2400H-6204JAN93
22、 N256-3VW3400H-6304JAN93 N256-4VW4400H-6404JAN93 N-1401-12NVW3/450H-1324JAN93 N-1401-16NVW150H-1404JAN93 N-1401-20NVW1-1/450H-1464JAN93 SAE J1942-1 Revised MAY2002 -4- 4.Aeroquip Corporation Aeroquip Industrial Americas Group Technical Center 1660 Indian Wood Circle Maumee, OH 43537-4069 Ph: (419) 8
23、91-7600 Fax: (419) 891-7790 TABLE 2AEROQUIP CORPORATION LISTING Hose Number Applic. Code Hose ID MAWP (PSI)Fittings Fire Sleeve Listing Date 1503-4HF3/163000400 Type,4400 Type624-1120NOV97 1503-5HF1/43000400 Type,4400 Type624-1120NOV97 1503-6HF5/162250400 Type,4400 Type624-1420NOV97 1503-8HF13/32200
24、0400 Type,4400 Type624-1620NOV97 1503-10HF1/21750400 Type,4400 Type624-1820NOV97 1503-12HF5/81500400 Type,4400 Type624-2020NOV97 1503-16HF7/8800400 Type,4400 Type624-2420NOV97 1503-20HF1-1/8625400 Type,4400 Type624-3020NOV97 1503-24HF1-3/8500400 Type,4400 Type624-3220NOV97 1503-32HF1-13/16350400 Typ
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J1942-1-2002 Qualified Hoses for Marine Applications J1942 2002
链接地址:https://www.31doc.com/p-3678338.html