SAE J2123-1998 Numbering System for Taps.pdf
《SAE J2123-1998 Numbering System for Taps.pdf》由会员分享,可在线阅读,更多相关《SAE J2123-1998 Numbering System for Taps.pdf(14页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243 TO PLACE A DOCU
3、MENT ORDER; (724) 776-4970 FAX: (724) 776-0790 SAE WEB ADDRESS http:/www.sae.org Copyright 1998 Society of Automotive Engineers, Inc. All rights reserved.Printed in U.S.A. SURFACE VEHICLE 400 Commonwealth Drive, Warrendale, PA 15096-0001 RECOMMENDED PRACTICE Submitted for recognition as an American
4、National Standard J2123 REV. OCT1998 Issued1990-11 Revised1998-10 Supserseding J2123 SEP95 Numbering System for Taps 1.Scope This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, a
5、nd Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1 Caution must be taken when assigning codes to prevent specifying taps that cannot be phy
6、sically or economically manufactured. NOTE 2 The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3 In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards
7、 of this report are retrieved, combined, or used in connection with any software. 2.References 2.1Applicable Publications The following publications (latest revision) form a part of the specification to the extent specified herein. NOTE Reference information not specified to be manufacturer s standa
8、rd practices. Manufacturer to supply additional technical information upon request. 2.1.1ASME PUBLICATIONS Available from American Society of Mechanical Engineers Order Department, 22 Law Drive, Box 2300, Fairfield, New Jersey 07007-2300. (The publications are also available through American Nationa
9、l Standards Institute.) ASME B94.9 Taps Cut and Ground Threads 2.2Related Publications The following publications are provided for information purposes only and are not a required part of this document. 2.2.1NUMBERING SYSTEMS SOFTWARE Software products may exist to assist in the use of the standard.
10、 The following software product(s) are listed for information purposes only and do not constitute part of this document. SAE expressly disclaims any responsibility for the operation of any Software used in connection with your use of this report. SAE J2123 Revised OCT1998 -2- 2.2.1.1Datom Engineerin
11、g Software, Inc., Publication Available from Datom Engineering Software, Inc., 561 Somerset, Suite 3, Crystal Lake, IL 60014, (815) 477-3380. Datom Engineering Software, Inc., TMS III-Drills-Electronic Reference Manual Nomenclature, Definitions, Sizes, and Tolerances of Twist Drills 2.2.2ISO PUBLICA
12、TIONS Available from International Organization for Standardization, 1 Rue DeVarembe, Case Postal 56, CH1211 Geneva 20 Switzerland. (The publications are also available through American National Standards Institute.) ISO 529 Short machine taps and hand taps Second Edition ISO 2283 Long shank machine
13、 taps with nominal diameters from 3 to 24 mm and 1/8 to 1 in First Edition (Amendment 1-1977) (Erratum Aug. 1976) ISO 2284 Hand taps for parallel and taper pipe threads General dimensions and marking Third Edition ISO 2857 Ground thread taps for ISO metric threads of tolerances 4H to 8H and 4G to 6G
14、 Course and fine pitches Manufacturing tolerances on the threaded portion First Edition (Amendment 1-1984) (Amendment 2-1986) (Corrigendum 1-1990) ISO 5967 Taps and thread cutting Nomenclature of the main types and terminology First Edition ISO 5969 Ground thread taps for pipe threads G series and R
15、p series Tolerances on the threaded portion First Edition (Corrigendum 1-1991) ISO 8051 Long shank taps with nominal diameters from M3 to M10 Taps with reinforced shank and recess First Edition ISO 8830 High speed steel machine taps with ground threads Technical specifications First Edition 2.2.3JIS
16、 PUBLICATIONS Available from Japanese Industrial Standards Committee, c/o Standards Department, Agency of Industrial Science and Technology, Ministry of International Trade and Industry, 1-3-1, Kasumigaseki, Chiyoda-ku, Tokyo 100, Japan. (The publications are also available through American National
17、 Standards Institute.) JIS B4430 Short Machine Taps and Hand Taps for Metric Threads Errata 1994 JIS B4432 Hand Taps for Unified Coarse Thread JIS B4433 Nut Taps JIS B4438 Hand Taps for Unified Fine Thread JIS B4439 Hand Taps for Sewing Machine Thread JIS B4445 Hand Taps for Pipe Threads for Paralle
18、l Threads JIS B4446 Hand Taps for Pipe Threads for Taper Threads 2.2.4USCTI PUBLICATIONS Available from United States Cutting Tool Institute, 1300 Summer Avenue, Cleveland, OH 44115. Handbook of Standard Taps 3.Numbering System 3.1Formats The basic numbering system is subdivided into two formats for
19、 taps: 3.1.1FORMAT 21 POSITION Taps with overall lengths which comply with the referenced Standards. 3.1.2FORMAT 26 POSITION For Extension, Pulley, and Other Taps with overall lengths which do not comply with the referenced Standards. SAE J2123 Revised OCT1998 -3- 3.2Content of Numbering System The
20、numbering system utilizes 21 and 26 positions to fully describe the various dimensions, types, materials, and characteristics of taps. Figure 1 illustrates the content and sequence of the 21 positions in the numbering system for taps whose overall lengths comply with the referenced Standards. FIGURE
21、 1 21 POSITION FORMAT SAE J2123 Revised OCT1998 -4- Figure 2 illustrates the content and sequence of the 26 positions in the numbering system for extension taps, pulley taps, and taps whose overall lengths do not comply with the referenced Standards. FIGURE 2 26 POSITION FORMAT 3.3Positions The cont
22、ent of each position is explained in detail in the following sections: 3.3.1POSITIONS 1 AND 2, CATEGORY AND NOUN Positions 1 and 2 will always be alphabetical. The following designations have been assigned: Position 1: T designates TOOL Position 2: T designates TAP 3.3.2POSITION 3, TYPE Position 3 w
23、ill be alpha or numeric based on the type of tap. The following codes have been assigned for taps without oil holes: 1 Standard Straight Thread (Fractional, Machine Screw, or Metric) 2 Taper Pipe 3 Straight Pipe 4 Pulley 5 Nut 6 Thread Forming 7 Standard Straight Thread Screw Thread Insert (S.T.I.)
24、8 Extension 9 Short Thread Length W Taper Pipe Small Shank (1/8 in nominal diameter) X Straight Pipe Small Shank (1/8 in nominal diameter) SAE J2123 Revised OCT1998 -5- The following codes have been assigned for taps with thru oil holes: A Standard Straight Thread (Fractional, Machine Screw, or Metr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J2123-1998 Numbering System for Taps J2123 1998
链接地址:https://www.31doc.com/p-3678345.html