SAE J2223-1-1998 Connections for On-Board Road Vehicle Electrical Wiring Harnesses.Part 1.pdf
《SAE J2223-1-1998 Connections for On-Board Road Vehicle Electrical Wiring Harnesses.Part 1.pdf》由会员分享,可在线阅读,更多相关《SAE J2223-1-1998 Connections for On-Board Road Vehicle Electrical Wiring Harnesses.Part 1.pdf(7页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243 TO PLACE A DOCU
3、MENT ORDER: (724) 776-4970 FAX: (724) 776-0790 SAE WEB ADDRESS http:/www.sae.org Copyright 1998 Society of Automotive Engineers, Inc. All rights reserved.Printed in U.S.A. SURFACE VEHICLE 400 Commonwealth Drive, Warrendale, PA 15096-0001 STANDARD Submitted for recognition as an American National Sta
4、ndard J2223-1 REV. DEC1998 Issued1994-02 Revised1998-12 Superseding J2223/1 FEB94 (R) Connections for On-Board Road Vehicle Electrical Wiring Harnesses Part 1: Single-Pole ConnectorsFlat Blade Terminals Dimensional Characteristics and Specific Requirements This document is technically equivalent to
5、ISO 8092/1. ForewordThis document has been changed from a Draft Technical Report to a Standard. It has also changed to comply with the new SAE Technical Standards Board Format. Definitions have changed to Section 3. All other section numbers have changed accordingly. SAE J2223 consists of the follow
6、ing parts: SAE J2223-1Connections for On-Board Road Vehicle Electrical Wiring HarnessesPart 1: Single Pole ConnectorsFlat Blade TerminalsDimensional Characteristics and Specific Requirements SAE J2223-2Connections for On-Board Road Vehicle Electrical Wiring HarnessesPart 2: Tests and General Perform
7、ance Requirements SAE J2223-3Connections for On-Board Road Vehicle Electrical Wiring HarnessesPart 3: Multipole ConnectorsFlat Blade TerminalsDimensional Characteristics and Specific Requirements 1.ScopeThis SAE Standard specifies dimensional characteristics of flat blades of single-pole connectors
8、and specific requirements for on-board electrical harnesses of road vehicles, which can be fitted into female connectors such as those given as in Appendix A. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
9、2.References 2.1Applicable PublicationsThe following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.1SAE PUBLICATIONSAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001
10、. SAE J2223/2Connections for On-Board Road Vehicle Electrical Wiring HarnessesPart 2: Tests and General Performance Requirements SAE J2223/3-Connections for On-Board Road Vehicle Electrical Wiring HarnessesPart 3: Multipole ConnectorsFlat Blade TerminalsDimensional Characteristics and Specific Requi
11、rements SAE J2223-1 Revised DEC1998 -2- 2.1.2ISO PUBLICATIONAvailable from ANSI, 11 West 42nd Street, New York, NY 10036-8002. ISO 8092/1Single pole connector tabsDimensions and specific requirements 3.DefinitionsSee SAE J2223-2, Section 3. 4.Dimensional CharacteristicsBlades shall conform to dimens
12、ions given in Figure 1 and Table 1. NOTEDetails not specified are left to the manufacturers choice. FIGURE 1FLAT BLADE DIMENSIONS SAE J2223-1 Revised DEC1998 -3- 5.Specific Performance RequirementsBlades for single-pole connections shall be in conformity with the general performance requirements of
13、SAE J2223-2, and shall meet the following specific requirements. NOTEA blade without a hole requires external means of retention to the mating part. 6.Connection Forces and Disconnection ForcesSingle-pole connectors, tested as in SAE J2223-2 (see 4.3), shall meet the requirements as in Table 2. NOTE
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J2223-1-1998 Connections for On-Board Road Vehicle Electrical Wiring Harnesses.Part J2223 1998 On
链接地址:https://www.31doc.com/p-3678348.html