SAE J214-1986 HYDRAULIC CYLINDER TEST PROCEDURE.pdf
《SAE J214-1986 HYDRAULIC CYLINDER TEST PROCEDURE.pdf》由会员分享,可在线阅读,更多相关《SAE J214-1986 HYDRAULIC CYLINDER TEST PROCEDURE.pdf(11页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243 TO PLACE A DOCU
3、MENT ORD724ER; (724) 776-4970 FAX: (724) 776-0790 SAE WEB ADDRESS http:/www.sae.org Copyright 1986 Society of Automotive Engineers, Inc. All rights reserved.Printed in U.S.A. SURFACE VEHICLE 400 Commonwealth Drive, Warrendale, PA 15096-0001 RECOMMENDED PRACTICE Submitted for recognition as an Americ
4、an National Standard J214 REAF. MAR86 Issued1972-01 Reaffirmed1986-03 Superseding J214 OCT80 HYDRAULIC CYLINDER TEST PROCEDURE ForewordThis Reaffirmed Document has been changed only to reflect the new SAE Technical Standards Board format. 1.ScopeThis test procedure describes tests for determining ch
5、aracteristics of hydraulic cylinders as used on construction and industrial mobile machinery as referenced in SAE J1116. In this code, metric equivalents are established according to SAE J916. These characteristics are to be recorded on data sheets similar to the ones shown herein. Two sets of data
6、sheets are to be submitted for each cylinder, one set at 120 F (49 C) and one at 180 F (82 C). 1.1PurposeThis test procedure establishes conditions for cylinder tests, outlines a procedure for tests, and describes a method of presenting cylinder test data. 1.1.1The procedure specifies methods for de
7、termining leakage rate, packing drag, proof pressure capacity, and endurance capacity. 2.References 2.1Applicable PublicationsThe following publications form a part of the specification to the extent specified herein. Unless otherwise indicated the latest revision of SAE publications shall apply. 2.
8、1.1SAE PUBLICATIONSAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. SAE J916Rules for SAE Use of SI (Metric) Units SAE J1116Categories of Off-Road Self-Propelled Work Machines 3.Material And Apparatus 3.1Test FluidTest fluid shall preferably be a mineral base oil designed for h
9、ydraulic service. Fluid viscosity shall be within the limits of 95115 SUS (438.9531.3 cs) at 120 F (49 C) and 5054 SUS (231249.5 cs) at 180 F (82 C). The test circuit shall be provided with 25 m absolute filtration. 3.2Pressure MeasurementsPressure measurements shall be accurate within 2.0%. 3.3Flow
10、 MeasurementFlow measurement shall be accurate within 2.0%. SAE J214 Reaffirmed MAR86 -2- 3.4Temperature Measurement and ControlFluid temperature shall be measured at the entrance to the cylinder by means of a thermometer or thermocouple. If a means of measuring temperature of fluid under pressure i
11、s not available, or if temperature change from reservoir to cylinder inlet is kept to a minimum, reservoir temperature is acceptable. Fluid temperature shall be maintained at the prescribed level through the test within 5 F (2.8 C). 3.5The test setup shall not impose side loads upon either the cylin
12、der under test or the slave cylinder. 4.General Definitions And Test Conditions 4.1Internal leakageshall be measured in inches (millimetres) per minute of shaft movement at a specified pressure. 4.2Fluid temperatureshall be 120 F and 180 F (49 C and 82 C) for standard tests and the test cylinder sha
13、ll be stroked prior to test runs to eliminate air from the circuit and to allow the cylinder components to heat up to the test temperature. 4.3Designated pressureof a cylinder shall be considered as the maximum pressure at which the manufacturer recommends continuous duty. 4.4Proof pressureis to be
14、defined as the maximum pressure which can be applied that will not cause any permanent set or deformation. Normally, this is never less than 200% designated pressure. 4.5Packing dragshall be defined as the amount of pressure necessary to move the piston with all external (either mechanical or hydrau
15、lic) forces removed or in balance. 4.6Rod endis the cylinder end closure which covers the differential area between the bore and the piston rod. 4.7Cap endis the cylinder end closure which completely covers the bore area. 4.8Rod leakageis defined as the oil that leaks by the rod packing. This leakag
16、e is associated with rod movement and is measured in cubic inches (or litres) per number of cycles. 5.Test 1 - Internal Leakage 5.1Figure 1 shows a recommended circuit for determining internal leakage. 5.2Position the piston of the cylinder under test at the approximate midpoint of the cylinder. 5.3
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J214-1986 HYDRAULIC CYLINDER TEST PROCEDURE J214 1986
链接地址:https://www.31doc.com/p-3678379.html