圆柱齿轮齿厚圆柱测量M 值及公法线长度的计算机算法.pdf
《圆柱齿轮齿厚圆柱测量M 值及公法线长度的计算机算法.pdf》由会员分享,可在线阅读,更多相关《圆柱齿轮齿厚圆柱测量M 值及公法线长度的计算机算法.pdf(3页珍藏版)》请在三一文库上搜索。
1、第 2 9 卷 增刊 光电工程 Vol.29, Sup 2 0 0 2 年 1 2 月 Opto-Electronic Engineering Dec, 2002 文章编号:1 0 0 3 - 5 0 1 X ( 2 0 0 2 ) S u p - 0 1 1 7 - 0 3 圆柱齿轮齿厚圆柱测量 M 值及 公法线长度的计算机算法 江 姬 嫔 (中国科学院光电技术研究所,四川 成都 610209) 摘要: 介绍一种适合各种渐开线圆柱齿轮齿厚圆柱测量 M 值及公法线长度的计算程序。根据圆柱 齿轮测量的相关计算公式,采用数值逼近法编程近似计算出测量尺寸,计算精度可根 据需要选 取,操作简单、快捷,
2、结果准确,大大简化了非标齿轮齿厚圆柱测量 M 值及公法线长度复杂的手 工计算,是非标齿轮制造检测过程中非常实用的计算程序。 关键词:齿轮参数测量;圆柱齿轮;圆柱测量;计算机辅助检测 中图分类号:TG86 文献标识码:A Computer algorithm for measuring span between two cylinders in cylindrical gear thickness and common normal length measurement JIANG Ji-pin (Institute of Optics and Electronics, Chinese Acad
3、emy of Sciences, Chengdu 610209, China) Abstract: A computer program that is suitable for measurement of span between two cylinders in cylindrical gear thickness and common normal length of various kinds of involute cylindrical gears. The measured sizes can be approximately calculated with digital a
4、pproximation method according to the correlative calculation formula for cylindrical gear measurement. The calculation accuracy can be selected according to the demands. Operating is simple, quick and the results are accurate, thus greatly simplifies the complex manual calculation in span measuremen
5、t between two ex- circles in cylindrical gear thickness and common normal length and it is a very practical calculation program in detection process for non-standard gear manufacturing. Key words: Gear tooth parameter measurement; Cylindrical gear; Cylindrical measurement; Computer aided testing 引 言
6、 在齿轮加工、检测过程中,齿厚圆柱测量及公法线长度测量是既简便而又比较精确的方法。因此,应 用非常普遍。对于标准圆柱齿轮,齿厚圆柱测量 M 值及公法线长度和跨齿数,一般均可通过查表获得。但 是,对于变位齿轮或斜齿轮则不能通过查表直接获得,必须根据每一齿轮参数由一系列公式手工计算求出, 这不仅是一项很繁琐的工作,而且很易出错。笔者通过对现有的计算方法进行分析、整理,并编成计算机 程序,对于渐开线圆柱齿轮,无论是标准的还是变位的、直齿还是斜齿,只要输入参数,立刻得出结果, 收稿日期:2 0 0 2 - 0 4 - 0 5 ;收到修改稿日期:2 0 0 2 - 0 6 - 1 4 作者简介:江姬嫔
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 圆柱齿轮齿厚圆柱测量M 值及公法线长度的计算机算法 圆柱齿轮 圆柱 测量 公法 长度 计算机 算法
链接地址:https://www.31doc.com/p-3704017.html