模具设计合理化.pdf
《模具设计合理化.pdf》由会员分享,可在线阅读,更多相关《模具设计合理化.pdf(182页珍藏版)》请在三一文库上搜索。
1、? Rationalization of Mold Design ? MoldZen Technology Co., Ltd. ? Brian Tsai ? ? ? ?!?“#$ %?ABC D?EF? G?HIJD?K7L MNOPQRSJ?TU?VW?“X? ?TUYZ ?K?K ?K?_aHI ?b5?PQc?dJef?Kg 7hRSJ?TU ijk?lm89?n%?g A?9?2 I.?=? ?Aa?Aa: PMMA ?*B?*B?: 400 BB (?) TUTU: ?CA?CA, DEFGDEFG CAE ?H?H IZJK:;CAEL?MNOPQ? R? ST?U?VZRTU ?
2、W? ?W? /!?9?, XJe*Y? ?,-?78?A?. HI?k?, Z?| dDEF _?W? _?W? 1?a?g ( 5- 20 -) , /!?9?S“b )?ag*c, “de?) ?B?l?O fi ?:O ? fi ? fi ? ? Sprue ? Main Runner ? Part O Gate fl a? Cold Slug Well +? Branch Runner fi ?| fi ?| ?;ST?:O ?Aa?ABS ?R?*B?80 Ton ?G?G?G?G? LCD TV BezelLCD TV Bezel Material?ABS Application
3、?LCD TV Clamp force?400 Ton (1 Cav. ) fl a? fl a? /?/? fl a? fl a? fl a? d 2d ? Secondary runner d ? Primary runner O Gate ? Cavity :;Y?E?MN?:;Y?E?MN? ?uv3? Z?B?O? ?A? :;Y?E?S“D?A?O ?=? 1?E?=?1?E?=? Y?1?_? ?17” TFT LCD G? Aa?ABS 1?E?=? 1?E?_ 1?E O?O? O?;? ?_?aDO?|? ?OS;ST?aij?O ?OS? ?R0?O?“?d? y?Jet
4、ting? y?y? Jetting O Jetting starting at the gate, spreading over the entire molded part y?y? y?(Jetting)?A: Y?fi fl (?Hyz?O)?E ?fi fl ?“? ;?O“”y?;?O“”y? 0? Poor ? Good ?O?“”y?O?“”y? 0? Poor ? Good O?iy?X?yO?iy?X?y O?g?l?=?H?(tab) O?“(fan)O? ?“SC)? y?“” ?y?dD?G; CAE L?H? PQa?)O?shear rate? ?)Aa?dS“?
5、 ;O“”y?;O“”y? ;?O“”y?;?O“”y? 0? Poor ? Good ?7?7? ?:O?:O ?(?( ?O Fan Gate 14” ?( ? by JSW O Tab Gate 10.4” ?( ? by Toshiba ?“?O?“?O? L = 0.5 0.75 mm W = O?- ( mm ) gate width in mm A = ?cg? ( mm2) surface area of cavity in mm2 n = Aa? material constant 0.6 for PE, PS 0.7 for POM, PC, PP 0.8 for CA,
6、PMMA, PA 0.9 for PVC h = n t h = OE-( gate thick. in mm ) t = ?DE( wall thick. in mm ) W tL h 30 An W ? “O?“O? L= 1.3mm W= w= O?- mm gate width in mm A= ?cg? mm2 surface area of cavity in mm2 n= Aa? material constant 0.6 for PE, PS 0.7 for POM, PC, PP 0.8 for CA, PMMA, PA 0.9 for PVC OE- gate thick.
7、 in mm t= ?DE wall thick. in mm 30 ?n h1= n th2= wh1/D ? O? O? W= w= O?- mm gate width in mm A= ?cg? mm2 surface area of cavity in mm2 n= Aa? material constant 0.6 for PE, PS 0.7 for POM, PC, PP 0.8 for CA, PMMA, PA 0.9 for PVC OE- gate thick. in mm = nt O?- land length in mm t= ?DE wall thick. in m
8、m 30 ?n L1 = 0.50.75L2= h+( w/2 ) O?O? L= 0.50.75mm W= w= O?- mm gate width in mm A= ?cg? mm2 surface area of cavity in mm2 n= Aa? material constant 0.6 for PE, PS 0.7 for POM, PC, PP 0.8 for CA, PMMA, PA 0.9 for PVC OE- gate thick. in mm t= ?DE wall thick. in mm 30 ?n h1= n th2= 0.9 t ?|O?|O? L = 0
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 模具设计 合理化
链接地址:https://www.31doc.com/p-3713888.html