07-30159027-DC.pdf
《07-30159027-DC.pdf》由会员分享,可在线阅读,更多相关《07-30159027-DC.pdf(21页珍藏版)》请在三一文库上搜索。
1、a Date: 8 January 2007 Origin: European Latest date for receipt of comments: 30 April 2007 Project no.: 2006/03228 Responsible committee: RAE/3/-/2 Rolling bearings and lubricants Interested committees: RAE/3 Title: Draft BS EN 14865-1 Railway Applications - Axlebox lubricating greases - Part 1: Met
2、hod to test the ability to lubricate ordinary-speed vehicles with speeds up to 200 km/h and high- speed vehicles with speeds up to 300 km/h Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede NONE . If you are
3、 aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 April 2007. This draft is issued to allow comments from interested pa
4、rties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 19
5、88 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ord
6、ersbsi-. British, International and foreign standards are also available from BSI Customer Services. British Standards on CD or Online are available from British Standards Publishing Sales Limited. Tel: 01344 404409 or email bsonlinetechindex.co.uk. Information on the co-operating organizations repr
7、esented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:
8、/www.bsi-. Direct tel: 020 8996 7445 Responsible Committee Secretary: K Seyde (BSI) E-mail: keith.seydebsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 6.1 DPC: 07/30159027 DC b Introduction This draf
9、t standard is based on European discussions in which the UK took an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Standard. If no comments are received to the contrary, then the UK will approve this draft and implement it as a Briti
10、sh Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publish the official English Language text unchanged as
11、a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate atten
12、tion by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of
13、Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting com
14、ments and how to obtain a blank electronic version of a comment form are available from the BSI web site at:http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/
15、Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection
16、. 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. EUROPEAN STA
17、NDARD NORME EUROPENNE EUROPISCHE NORM DRAFT prEN 14865-1 December 2006 ICS 45.040; 75.100 English Version Railway Applications - Axlebox lubricating greases - Part 1: Method to test the ability to lubricate ordinary-speed vehicles with speeds up to 200 km/h and high-speed vehicles with speeds up to
18、300 km/h Applications ferroviaires - Graisses lubrifiantes pour botes dessieux - Partie 1 : Mthode dessai daptitude lubrifier les vhicules circulant des vitesses classiques jusqu 200 km/h et les vhicules circulant grande vitesse jusqu 300 km/h This draft European Standard is submitted to CEN members
19、 for enquiry. It has been drawn up by the Technical Committee CEN/TC 256. If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without an
20、y alteration. This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the
21、official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia
22、, Spain, Sweden, Switzerland and United Kingdom. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation. Warning : This document is not a European Standard. It is distributed for
23、review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitat
24、ion in any form and by any means reserved worldwide for CEN national Members. Ref. No. prEN 14865-1:2006: E prEN 14865-1:2006 (E) 2 Contents Page Foreword3 Introduction.4 1 Scope 5 2 Normative references5 3 Terms and definitions .5 4 Symbols7 5 Testing principle8 6 Reagents and material 8 7 Test equ
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 07 30159027 DC
链接地址:https://www.31doc.com/p-3726145.html