06-30158977-DC.pdf
《06-30158977-DC.pdf》由会员分享,可在线阅读,更多相关《06-30158977-DC.pdf(41页珍藏版)》请在三一文库上搜索。
1、a Date: 19 December 2006 Origin: European Latest date for receipt of comments: 31 March 2007 Project no.: 2006/03211 Responsible committee: ISE/8 Steel pipes Interested committees: Title: Draft BS EN 1124-3 Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for
2、waste water systems - Part 3: System X - Dimensions Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN1124-3 : 1999 and partially supersede NONE . If you are aware of a current national standard which may be affected, please notify
3、the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 March 2007. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No ac
4、knowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purpose
5、s. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available fr
6、om BSI Customer Services. British Standards on CD or Online are available from British Standards Publishing Sales Limited. Tel: 01344 404409 or email bsonlinetechindex.co.uk. Information on the co-operating organizations represented on the committees referenced above may be obtained from the respons
7、ible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7147 Responsible Committee Secretary: F P S
8、lot (BSI) E-mail: peter.slotbsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 6.1 DPC: 06/30158977 DC Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:54 GMT+
9、00:00 2006, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK took an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Standard. If no comments are received to the contrary,
10、then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obli
11、ged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to e
12、nsure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. C
13、omments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as gi
14、ven in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at:http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB
15、 Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amen
16、d to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, an
17、d Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM DRAFT prEN 1124-3 December 2006 ICSWill supersede EN 1124-3:1
18、999 English Version Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 3: System X - Dimensions Tubes et raccords de tube souds longitudinalement en acier inoxydable, manchon enfichable pour rseaux dassainissement - Partie 3: Systm
19、e X - Dimensions Rohre und Formstcke aus lngsnahtgeschweitem, nichtrostendem Stahlrohr mit Steckmuffe fr Abwasserleitungen - Teil 3: System X - Mae This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 165. If this draft becomes
20、a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This draft European Standard was established by CEN in three official versions (En
21、glish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Cz
22、ech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Recipients of this draft are invited to submit,
23、 with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a Eu
24、ropean Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. prEN 1124
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 06 30158977 DC
链接地址:https://www.31doc.com/p-3726318.html