07-30175126-DC.pdf
《07-30175126-DC.pdf》由会员分享,可在线阅读,更多相关《07-30175126-DC.pdf(19页珍藏版)》请在三一文库上搜索。
1、a Date: 24 December 2007 Origin: International Latest date for receipt of comments: 31 March 2008 Project no.: 2007/03326 Responsible committee: PRI/66 Rubber and plastics tubing, hoses and hose assemblies Interested committees: Title: Draft BS ISO 1436 Rubber hoses and hose assemblies Wire-braid-re
2、inforced hydraulic types for oil- based or water-based fluids Specification Supersession information: If this document is published as a standard, the UK implementation of it will supersede ISO1436-2 and partially supersede. NONE If you are aware of a current national standard which may be affected,
3、 please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 March 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to pub
4、lication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for b
5、riefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are al
6、so available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in
7、 this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7773 Responsible Committee Secretary: Ms Sue Barden (BSI) E-mail: sue.bardenbsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 89
8、96 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 07/30175126 DC Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:43:33 GMT+00:00 2008, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK h
9、as taken an active part. Your comments on this draft are invited and will assist in the preparation of the consequent standard. Comments submitted will be reviewed by the relevant BSI committee before sending the consensus UK vote and comments to the international secretariat, which will then decide
10、 appropriate action on the draft and the comments received. If no comments are received to the contrary, then the UK will approve this draft. If the international standard is approved, it is possible the text will be published as an identical British Standard. UK Vote Please indicate whether you con
11、sider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All
12、 comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any
13、 comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web
14、site at: http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed
15、change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious
16、problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:43:33 GMT+00:00 2008,
17、Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AN
18、D USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RI
19、GHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 1436 International Organization for Standardization, 2007 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 45/SC 1 Voting begins on: 2007-12-12
20、 Secretariat: DSM Voting terminates on: 2008-05-12 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification Tuyaux et flexibles en caoutchouc Types hydrauliques avec armature de fils mtalliques tresss pour fluides base dhuile ou base de
21、au Spcifications Revision ISO 1436-1:2001 and ISO 1436-2:2005 ICS 23.100.40; 83.140.40 In accordance with the provisions of Council Resolution 15/1993 this document is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993, ce document est distribu e
22、n version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel quil
23、 est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:43:33 GMT+00:00 2008, Uncontrolled Copy, (c) BSI ISO/DIS
24、 1436 ii ISO 2007 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 07 30175126 DC
链接地址:https://www.31doc.com/p-3726376.html