08-30176215-DC.pdf
《08-30176215-DC.pdf》由会员分享,可在线阅读,更多相关《08-30176215-DC.pdf(42页珍藏版)》请在三一文库上搜索。
1、a Date: 10 January 2008 Origin: International Latest date for receipt of comments: 30 April 2008 Project no.: 2008/00142 Responsible committee: PSE/17/2 Transmission pipelines Interested committees: Title: Draft BS ISO 15590-1 Petroleum and natural gas industries - Induction bends, fittings and flan
2、ges for pipeline transportation systems Part 1: Induction bends Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify th
3、e secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 April 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No ackn
4、owledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes.
5、 Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available from
6、 BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may b
7、e found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7445 Responsible Committee Secretary: K Seyde (BSI) E-mail: keith.seydebsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20
8、8996 7001 Form 36 Version 7.0 DPC: 08/30176215 DC Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 07:06:51 GMT+00:00 2008, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active par
9、t. Your comments on this draft are invited and will assist in the preparation of the consequent standard. Comments submitted will be reviewed by the relevant BSI committee before sending the consensus UK vote and comments to the international secretariat, which will then decide appropriate action on
10、 the draft and the comments received. If no comments are received to the contrary, then the UK will approve this draft. If the international standard is approved, it is possible the text will be published as an identical British Standard. UK Vote Please indicate whether you consider the UK should su
11、bmit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be subm
12、itted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitte
13、d electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/www.bsi
14、- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secre
15、tariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been enc
16、ountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 07:06:51 GMT+00:00 2008, Uncontrolled Copy, (c)
17、 BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
18、 INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE
19、 AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 15590-1 International Organization for Standardization, 2008 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 67/SC 2 Voting begins on: 2008-01-04 Secretariat: NEN V
20、oting terminates on: 2008-06-04 Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 1: Induction bends Industries du ptrole et du gaz naturel Coudes dinduction, raccords et brides pour systmes de transport par conduites Partie 1: Coudes
21、 dinduction Revision of first edition (ISO 15590-1:2001) ICS 75.200 In accordance with the provisions of Council Resolution 15/1993 this document is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993, ce document est distribu en version anglaise
22、seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel quil est parvenu du sec
23、rtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 07:06:51 GMT+00:00 2008, Uncontrolled Copy, (c) BSI ISO/DIS 15590-1 ii ISO 200
24、8 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In d
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 08 30176215 DC
链接地址:https://www.31doc.com/p-3726601.html