08-30178375-DC.pdf
《08-30178375-DC.pdf》由会员分享,可在线阅读,更多相关《08-30178375-DC.pdf(16页珍藏版)》请在三一文库上搜索。
1、a Date: 26 November 2008 Origin: European Latest date for receipt of comments: 28 February 2009 Project no.: 2008/00642 Responsible committee: MTE/23 Woodworking machines Interested committees: Title: Draft BS EN 1218-2:2004/A1 Safety of woodworking machines - Tenoning machines Part 2: Double end te
2、noning and/or profiling machines fed by chain or chains Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN1218-2 : 2004 and partially supersede. NONE If you are aware of a current national standard which may be affected, please noti
3、fy the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 28 February 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication.
4、 No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing p
5、urposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from B
6、SI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be
7、found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 700
8、1 Form 36 Version 8.0 DPC: 08/30178375 DC Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are wel
9、come and will assist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obli
10、ged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to e
11、nsure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. C
12、omments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as gi
13、ven in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause
14、 No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to re
15、ad . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windo
16、ws is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 1218-2:2004 prA1 November 2008 ICS 79.120.10 English Version Safety of woodwor
17、king machines - Tenoning machines - Part 2: Double end tenoning and/or profiling machines fed by chain or chains Scurit des machines pour le travail du bois - Tenonneuses - Partie 2: Machines tenonner et/ou profiler chane ou chanes Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlit
18、zmaschinen - Teil 2: Doppelseitige Zapfenschneid- und Schlitzmaschinen und/oder Doppelendprofiler mit Kettenbandvorschub This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 142. This draft amendment A1, if approved,
19、 will modify the European Standard EN 1218-2:2004. If this draft becomes an amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amend
20、ment was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are
21、 the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer
22、land and United Kingdom. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITE
23、E FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1218-2:2004/prA1:2008: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45,
24、Uncontrolled Copy, (c) BSI EN 1218-2:2004/prA1:2008 (E) 2 Contents Page Foreword3 1 Modification to the Foreword .4 2 Modification to the Introduction.4 3 Modification to Clause 1, Scope.4 4 Modification to Clause 2, Normative references 4 5 Modification to 3.3, Definitions.5 6 Modification to Claus
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 08 30178375 DC
链接地址:https://www.31doc.com/p-3726614.html