08-30176974-DC.pdf
《08-30176974-DC.pdf》由会员分享,可在线阅读,更多相关《08-30176974-DC.pdf(11页珍藏版)》请在三一文库上搜索。
1、a Date: 23 January 2008 Origin: International Latest date for receipt of comments: 30 April 2008 Project no.: 2007/00280 Responsible committee: GEL/15/3/5 Flexible insulating sleeving for electrical purposes Interested committees: Title: Draft IEC 62329-3-101 ED 1 Heat shrinkable moulded shapes Part
2、 3 Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 101 Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance Supersession information: If this document is published as a s
3、tandard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRA
4、FT IS NOT CURRENT BEYOND 30 April 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without pri
5、or written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies
6、 of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be ob
7、tained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7205 Responsible Com
8、mittee Secretary: Mr A Ashrafi (BSI) E-mail: asghar.ashrafibsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 08/30176974 DC Licensed Copy: London South Bank University, London South Bank Unive
9、rsity, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent standard. If no commen
10、ts are received to the contrary, then the UK will approve this draft. There is a high probability that this text could be adopted by CENELEC as a reference document for harmonization or as a European Standard. Recipients of this draft are requested to comment on the text bearing in mind this possibi
11、lity. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts
12、 are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comm
13、ents in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a
14、 comment form are available from the BSI web site at: http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (
15、justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as a
16、n alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank Uni
17、versity, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/405/CD COMMITTEE DRAFT (CD) IEC/TC or SC: TC15 Project number IEC 62329-3-101 Ed. 1.0 Title of TC/SC: Solid Electrical Insulating Materials Date of circulation 2008-01-18 Closing date for comments 2008-04-18 Also of interest
18、to the following committees TC112 Supersedes document 15/364/CD and 15/385/CC Functions concerned: Safety EMC Environment Quality assurance Secretary: John A. Gauthier, USA Email: THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT SHOULD NOT BE USED FOR REFERENCE PURPOSES. RECIPIENTS OF T
19、HIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. Title: IEC 62329-3-101 Ed. 1.0: Heat shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requ
20、irements and compatibility performance - Sheet 101: Heat- shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. (Titre) : Introductory note This project began as IC 62329-3-100 Ed. 1.0: Heat shrinkable moulded shapes Part 3: Specificati
21、on for individual materials Sheet 100 to 107: Requirements for shape dimensions, material requirements and compatibility performance. It was decided at the last TC 15 plenary meeting in Prague (May 2007) to separate this project into the 3 following parts: IEC 62329-3-100 Ed. 1.0: Heat shrinkable mo
22、ulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 100: Heat-shrinkable moulded shape dimensions IEC 62329-3-101 Ed. 1.0: Heat shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, materia
23、l requirements and compatibility performance - Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. IEC 62329-3-102 Ed. 1.0: Heat shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, mate
24、rial requirements and compatibility performance - Sheet 102: Heat-shrinkable elastomeric moulded shapes, semi-rigid, material requirements and system performance FORM CD (IEC) 2002-08-08 Copyright 2008 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 08 30176974 DC
链接地址:https://www.31doc.com/p-3726630.html