《08-30179728-DC.pdf》由会员分享,可在线阅读,更多相关《08-30179728-DC.pdf(6页珍藏版)》请在三一文库上搜索。
1、Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30179728 DC Date: 28 October 2008 Origin: European Latest date for receipt of comments: 31 December 2008 Project no.: 2008/00966 Responsible com
2、mittee: MRE/1 Mining mechanical equipment and machinery Interested committees: Title: Draft BS EN 12321:2003/A1 Underground mining machinery - Specification for the safety requirements of armoured face conveyors Supersession information: If this document is published as a standard, the UK implementa
3、tion of it will supersede BS EN 12321:2003 and partially supersede NONE. If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURR
4、ENT BEYOND 31 December 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written
5、permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this dr
6、aft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the respo
7、nsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee S
8、ervice Centre (BSI) E-mail: a Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will
9、 assist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publis
10、h the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that al
11、l comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments shoul
12、d be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the ex
13、ample below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclau
14、se No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that
15、the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trade
16、mark of Microsoft Corporation. b Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 12321:2003 prA1 October 2008 ICS 73.100.40 English Version Underground mining machinery -
17、 Specification for the safety requirements of armoured face conveyors Machines dexploitation souterraine - Spcification relative aux prescriptions de scurit des transporteurs blinds chane raclettes Bergbaumaschinen unter Tage - Sicherheitsanforderungen an Kettenkratzerfrderer This draft amendment is
18、 submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 196. This draft amendment A1, if approved, will modify the European Standard EN 12321:2003. If this draft becomes an amendment, CEN members are bound to comply with the CEN/CENELEC Inter
19、nal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the r
20、esponsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary
21、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change w
22、ithout notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worl
23、dwide for CEN national Members. Ref. No. EN 12321:2003/prA1:2008: E Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI EN 12321:2003/prA1:2008 (E) 2 Foreword This document (EN 12321:2003/prA1:2008) has been prepared by Technical Committee
24、 CEN/TC 196 “Machines for underground mines - Safety”, the secretariat of which is held by DIN. This document is currently submitted to the Unique Acceptance Procedure. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, an
25、d supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI EN 12321:2003/pr
26、A1:2008 (E) 3 1 Modifications to 7.2 Marking Replace the 1st indent with the following: “ the business name and full address of the manufacturer and, where applicable, his authorised representative;“. Replace the 3rd indent with the following: “ designation of the machinery;“. 2 Modification to Anne
27、x ZA Replace the existing Annex ZA with the following: “ Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EG This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free T
28、rade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 98/37/EG, amended by 98/79/EG on machinery. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard i
29、n at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements except ESR 1.5.8 and 1.7.4 f) of that Directive and associated EFTA regulations. WARNING
30、Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI EN 12321:2003/prA1:2008 (E) 4 3 Addition of Annex ZB Add the fol
31、lowing Annex ZB: “ Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means
32、of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normat
33、ive clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements except ESR 1.5.8 and 1.7.4.2 u) of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI
链接地址:https://www.31doc.com/p-3727170.html