08-30189604-DC.pdf
《08-30189604-DC.pdf》由会员分享,可在线阅读,更多相关《08-30189604-DC.pdf(14页珍藏版)》请在三一文库上搜索。
1、a Date: 25 November 2008 Origin: European Latest date for receipt of comments: 28 February 2009 Project no.: 2008/02933 Responsible committee: ISE/26 Steel wire Interested committees: Title: Draft BS EN 10223-2 Steel wire and wire products for fences Part 2: Hexagonal steel wire netting for agricult
2、ural, insulation, and fencing purposes Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN10223-2 : 1998 and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary
3、 (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 28 February 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgem
4、ent will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electro
5、nic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Serv
6、ices. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the Br
7、itish Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Versio
8、n 8.0 DPC: 08/30189604 DC Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:05, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will as
9、sist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publish t
10、he official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all c
11、omments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should b
12、e compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the examp
13、le below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause
14、No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the
15、 mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademar
16、k of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:05, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM DRAFT prEN 10223-2 November 2008 ICS 77.140.65Will supersede EN 10223-2:1997 English Version Steel wire and w
17、ire products for fences - Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes Fils et produits trfils en acier pour cltures - Partie 2: Grillage mailles hexagonales en acier utilis dans lagriculture pour lisolation et les cltures Stahldraht und Drahterzeugnisse fr
18、Zune - Teil 2: Stahldrahtgeflecht mit sechseckigen Maschen fr landwirtschaftliche Zwecke, Isolierungen und Zune This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 30. If this draft becomes a European Standard, CEN members ar
19、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This draft European Standard was established by CEN in three official versions (English, French, German). A version i
20、n any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark
21、, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Recipients of this draft are invited to submit, with their comments,
22、 notification of any relevant patent rights of which they are aware and to provide supporting documentation. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EURO
23、PEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. prEN 10223-2:2008: E Licensed
24、Copy: London South Bank University, South Bank University, 31/01/2009 04:05, Uncontrolled Copy, (c) BSI prEN 10223-2:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4 Information to be supplied by the purchaser .8 5 Manufacture8 5.1 Base metal8 5.2 Fab
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 08 30189604 DC
链接地址:https://www.31doc.com/p-3727237.html