08-30176914-DC.pdf
《08-30176914-DC.pdf》由会员分享,可在线阅读,更多相关《08-30176914-DC.pdf(15页珍藏版)》请在三一文库上搜索。
1、a Date: 23 January 2008 Origin: International Latest date for receipt of comments: 30 April 2008 Project no.: 2008/00314 Responsible committee: GEL/15/3/5 Flexible insulating sleeving for electrical purposes Interested committees: Title: Draft BS EN 60684-3-271 ED.3 Flexible insulating sleeving - Pa
2、rt 3: Specifications for individual types of sleeving - Sheet 271: Heat-shrinkable elastomer sleevings, flame retarted, fluid resistant, shrink ratio 2:1 Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN60684-3-271 : 2004 and parti
3、ally supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 April 2008. This draft is issued to al
4、low comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyr
5、ight, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +
6、44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references
7、The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7205 Responsible Committee Secretary: Mr A Ashrafi (BSI) E-mail: asghar.ashrafibsi- Dr
8、aft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 08/30176914 DC Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:49:00 GMT+00:00 2008, Uncontrolled Copy, (c)
9、BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent standard. If no comments are received to the contrary, then the UK will approve this dra
10、ft. There is a high probability that this text could be adopted by CENELEC as a reference document for harmonization or as a European Standard. Recipients of this draft are requested to comment on the text bearing in mind this possibility. UK Vote Please indicate whether you consider the UK should s
11、ubmit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be sub
12、mitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitt
13、ed electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/www.bs
14、i- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secr
15、etariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been en
16、countered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:49:00 GMT+00:00 2008, Uncontrolled Copy, (c
17、) BSI 15/413/CD COMMITTEE DRAFT (CD) IEC/TC or SC: TC15 Project number IEC 60684-3-271 Ed. 3.0 Title of TC/SC: Solid Electrical Insulating Materials Date of circulation 2008-01-18 Closing date for comments 2008-04-18 Also of interest to the following committees TC112 Supersedes document 15/411/MCR F
18、unctions concerned: Safety EMC Environment Quality assurance Secretary: John A. Gauthier, USA Email: THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT SHOULD NOT BE USED FOR REFERENCE PURPOSES. RECIPIENTS OF THIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RE
19、LEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. Title: IEC 60684-3-271 Ed. 3.0: Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 271: Heat-shrinkable elastomer sleevings, flame retarded, fluid resistant, shrink ratio
20、 2:1 (Titre) : Introductory note FORM CD (IEC) 2002-08-08 Copyright 2008 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
21、You may not copy or “mirror“ the file or printed version of the document, or any part of it, for any other purpose without permission in writing from IEC. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:49:00 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/413/
22、CD 2 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheet 271: Heat-shrinkable elastomer sleevings, flame retarded, fluid resistant, shrink ratio 2:1 FOREWORD 1) The International Electrotechnical Commission (IEC) is a
23、 worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to ot
24、her activities, IEC publishes International Standards, Technical Specifications, Technical Reports, and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 08 30176914 DC
链接地址:https://www.31doc.com/p-3727351.html